|
| bowsaw |
|
|||
|
Anyone heard of, or had any expierience with these, they surely have to be better than stock manifold.
|
|||
| Top | |
|||
| NABAXT |
|
||
|
fakertaker has 'em in his au xr6, says they r pretty darn good, apparently they fit the au-ba's really well, and his xr6 isnt that slow, its actually pretty fast!!
|
||
| Top | |
||
| dsnow_01 |
|
|||
|
yeah my mate has some on his vt(please dont flame
 )..and they seem good...nice priced...my other mate put some on his XF Panel van. The guys who fitted them said that there better than the pacies at lower RPM's..but yeah they seemed to do the job..
cheapest extractors ive seen in SA are the Advanced headers. thanks |
|||
| Top | |
|||
| kezz |
|
||
|
ive got them on my car and it pulls alright. cant compare it to other extractors but like you said it has to be better than the stock manifold
_________________ Kezz's 5sp Box Car ---> RPD enhanced with a bunch of other stuff |
||
| Top | |
||
| bowsaw |
|
|||
|
Thanks , can get a set for 100 smackers, might buy em now.
|
|||
| Top | |
|||
| opto |
|
|||
|
Been running them for 6 months, similar or better that pacey 4499's.
Running Hi flow cat and 2.5 inch exhaust and 2 berklees, lovely deep sound good flow nice acceleration from low down on the rev range thru to top revs (sorry no on board tacho) You will be happy , just get a stainless steel heat shield to cut down engine bay temps
_________________ I post here cos the russian tank driver doesn't |
|||
| Top | |
|||
| prydey |
|
|||
|
do they have mandrel or press bends?
_________________ eb v8: low loud and fast. just how a v8 should be. i guess the big question is, is it fast enough... |
|||
| Top | |
|||
| samsEL |
|
||
|
bowsaw wrote: Thanks , can get a set for 100 smackers, might buy em now.
Can u get another set for $100.... 
|
||
| Top | |
||
| twr7cx |
|
|||
|
any extractors for $100.00 is a fine buy!
|
|||
| Top | |
|||
| Mr.Kiss |
|
|||
|
s**t thats cheap!!!
You could buy 4 sets of pacies for that much!
_________________ My Cars |
|||
| Top | |
|||
| twr7cx |
|
|||
|
EFmonty wrote: s**t thats cheap!!!
You could buy 4 sets of pacies for that much! Yeah, but we don't know if there new or second hand yet. |
|||
| Top | |
|||
| xcabbi |
|
||
|
prydey wrote: do they have mandrel or press bends?
They are press bent but they are not that bad. I had a set on my XF (which I still have for no reson in particular) and that thing used to pull pretty hard compared to the stock exhaust. I bought mine with a full zorst for 600 fitted. Still got the whole lot though. |
||
| Top | |
||
| 99 tonner |
|
|||
|
Value for money and performance they are great i have them on my Au and it gives BA XR6 turbos "standard" a run worth bragging about..........
_________________ T402 ISX 500hp daily driver |
|||
| Top | |
|||
| twirqurky |
|
||
|
So bowsaw, how did you get them for 100?
|
||
| Top | |
||
| Hyena |
|
|||
|
I've got these extractors too, and they don't seem to be holding back any of my other (vast!) engine work. I didn't notice any difference when I fitted them, but it came up trumps on the dyno and drag strip so they get the thumbs up from me
_________________
|
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 71 guests |
