Fordmods Logo

AU xr6 non VCT motor to 94" EF ghia 4.0 auto 

 

Page 1 of 1 [ 7 posts ] 

 
 Post subject: AU xr6 non VCT motor to 94" EF ghia 4.0 auto
Posted: Wed Apr 04, 2012 7:08 pm 
Parts Gopher
Offline
User avatar

Age: 63

Posts: 98

Joined: 23rd Mar 2009

Gallery: 5 images

Ride: 1994 EF

Location: Burnie
TAS, Australia

Hi guys
I have been offered an AU xr6 non VCT motor 130000 ks + tans & CPU $500,
My EF is getting tied so might do the conversion,
I have read about the sump or K frame mods needed & other small mods. + bell-housing swop on here
I have 4 question's:
1-should I replace EF cpu with Au xr6 CPU?
2-will trans fit without mods? tho nothing wrong with mine.
3- I'm running a wade 1636 in EF would there be any advantage installing that into Au xr6 ?
4- If so will shims be required number & size of shims ?

due to pick it up next week

any advice/guidance most appreciated
cheers
Dean
Top
 Profile  
 
 
 Post subject: Re: AU xr6 non VCT motor to 94" EF ghia 4.0 auto
Posted: Wed Apr 04, 2012 8:40 pm 
Moderator
Offline

Posts: 14489

Joined: 7th Nov 2004

Ride: AU XR8

Location: a shit suburb in sydney
NSW, Australia

devondevil wrote:
Hi guys
I have been offered an AU xr6 non VCT motor 130000 ks + tans & CPU $500,
My EF is getting tied so might do the conversion,
I have read about the sump or K frame mods needed & other small mods. + bell-housing swop on here
I have 4 question's:
1-should I replace EF cpu with Au xr6 CPU?
2-will trans fit without mods? tho nothing wrong with mine.
3- I'm running a wade 1636 in EF would there be any advantage installing that into Au xr6 ?
4- If so will shims be required number & size of shims ?

due to pick it up next week

any advice/guidance most appreciated
cheers
Dean


1) nope, use the ef ecu as au one is not a compatable ecu.
2) your trans will fit but best to get an au bellhousing..
3) the 1636 from the ef cannot be used in the au unless the ef rocker assembly is used due to different rocker ratio's..
Top
 Profile  
 
 
 Post subject: Re: AU xr6 non VCT motor to 94" EF ghia 4.0 auto
Posted: Wed Apr 04, 2012 9:24 pm 
Getting Side Ways
Offline

Age: 42

Posts: 508

Joined: 28th Feb 2009

Gallery: 9 images

Ride: Ed v8 fairmont wagon, wr450f

Power: 137 rwkw

devondevil wrote:
Hi guys
I have been offered an AU xr6 non VCT motor 130000 ks + tans & CPU $500,
My EF is getting tied so might do the conversion,
I have read about the sump or K frame mods needed & other small mods. + bell-housing swop on here
I have 4 question's:
1-should I replace EF cpu with Au xr6 CPU?
2-will trans fit without mods? tho nothing wrong with mine.
3- I'm running a wade 1636 in EF would there be any advantage installing that into Au xr6 ?
4- If so will shims be required number & size of shim

any advice/guidance most appreciated
cheers
Dean


i fitted au vct motor and box to my 94 ef wagon and is very easy, i ground the ridges off the front of the au sump so it was flush again and put 4 cuts on the sub frame seam but not the subframe to same width of the sump and just folded the seam over and tap in about 5-10mm and had 5mm clearance on the sump to crossmember. I had series 1 motor so changed knock senor over from ef motor,drop in the CAS and slightly adjusted the CAS lock bracket as it bolts up on the other side. I ran the au injectors on the ef intake as couple of vacum outlets differ and fitted ef xr6 computer for firmer shifts and abit better fuel/timing maps...

phill
Top
 Profile  
 
 
 Post subject: Re: AU xr6 non VCT motor to 94" EF ghia 4.0 auto
Posted: Thu Apr 05, 2012 8:49 am 
Parts Gopher
Offline
User avatar

Age: 63

Posts: 98

Joined: 23rd Mar 2009

Gallery: 5 images

Ride: 1994 EF

Location: Burnie
TAS, Australia

thanks very much TROYMAN & phill
that helped heaps & cleared the path to getting it done for me
have a great & safe Easter
cheers
Dean
Top
 Profile  
 
 
 Post subject: Re: AU xr6 non VCT motor to 94" EF ghia 4.0 auto
Posted: Thu Apr 05, 2012 11:48 am 
Parts Gopher
Offline
User avatar

Age: 63

Posts: 98

Joined: 23rd Mar 2009

Gallery: 5 images

Ride: 1994 EF

Location: Burnie
TAS, Australia

ps just another quick question
would it be easier to leave au bellhousing & every thing connected to motor to install ?

safe Easter all
cheers
Dean
Top
 Profile  
 
 
 Post subject: Re: AU xr6 non VCT motor to 94" EF ghia 4.0 auto
Posted: Thu Apr 05, 2012 1:23 pm 
Moderator
Offline

Posts: 14489

Joined: 7th Nov 2004

Ride: AU XR8

Location: a shit suburb in sydney
NSW, Australia

the au bellhousing needs to be bolted to the gearbox before fitting it to the engine..

but probably easier to put the engine and gearbox in together...
Top
 Profile  
 
 
 Post subject: Re: AU xr6 non VCT motor to 94" EF ghia 4.0 auto
Posted: Thu Apr 05, 2012 2:56 pm 
Parts Gopher
Offline
User avatar

Age: 63

Posts: 98

Joined: 23rd Mar 2009

Gallery: 5 images

Ride: 1994 EF

Location: Burnie
TAS, Australia

thanks TROYMAN
that's what ill do then mate, thanks very much appreciated
cheers
Dean
Top
 Profile  
 
Display posts from previous:
Sort by  
 Page 1 of 1  [ 7 posts ] 

Who is online

Users browsing this forum: No registered users and 33 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

 

 

It is currently Fri Mar 29, 2024 5:10 am All times are UTC + 11 hours

 

 

(c)2014 Total Web Solutions Australia - Australian Web Hosting and Domain Names