Fordmods Logo

Crow Cam 2222549 

 

Page 2 of 2 [ 21 posts ] Go to page Previous  1, 2

 
Posted: Wed May 04, 2005 11:25 pm 
Getting Side Ways
Offline
User avatar

Age: 39

Posts: 927

Joined: 6th Nov 2004

Ride: BA Falcon EGas

Location: Perth
WA, Australia

LG wrote:
The dev3hl won't need a new computer. But to get the absolute most out of it, it'd probably be wise.

The Crow Cam 2222549 is a Stage 3 cam, so idling may be way off.


No its actually a stage 2 cam mate, the stage 3 is the one above is the 2222543 which actually needs a chip to run.

I put that in mine and the idle was all over the place and I had to get the chiptorque chip for it, also to sort out A/F troubles.

As for actually answering the question that was asked, the stage 2 crow cam which you are asking about is a good mild cam that will run in your auto although you will rarely stall at the lights during idle while in drive. Other than that its a good value for money billet cam.

Hope that helps.

 

_________________

BA Falcon Futura on EGas. Stock as...

EF 5 speed manual; PH 4480 Pacemaker Headers; 2 1/2" Lukey Mandrel Bent System; Hi Flow Walker Cat; Stage 3 Crow Cam; ChipTorque Chip; 3" Mandrel Bent Intake; K&N Pod Filter; Low Pedders Suspension; 17" EL GT Champagne Rims; RPM Series Clutch

Top
 Profile  
 
 
Posted: Wed May 04, 2005 11:42 pm 
Oompa Loompa
Offline

Posts: 21

Joined: 6th Feb 2005

Location: Melbourne
VIC, Australia

my car runs fine with the crow stage 3. I had to get better valve springs but im not running antoher computer.

 

_________________

There is no substitue for cubic inches!

Top
 Profile  
 
 
Posted: Thu May 05, 2005 12:53 am 
Getting Side Ways
Offline
User avatar

Age: 38

Posts: 658

Joined: 5th Nov 2004

Ride: Falcon

Location: Melbourne
VIC, Australia

Opps my bad, i remembered reading somewhere, that someone had that one, and they said it was a stage 3.

 

_________________

Image

Top
 Profile  
 
 
Posted: Thu May 05, 2005 1:03 am 
Getting Side Ways
Offline
User avatar

Age: 39

Posts: 927

Joined: 6th Nov 2004

Ride: BA Falcon EGas

Location: Perth
WA, Australia

LG wrote:
Opps my bad, i remembered reading somewhere, that someone had that one, and they said it was a stage 3.


Well, i think they're wrong. Cause its lift and duration is very similar to the EF one.

 

_________________

BA Falcon Futura on EGas. Stock as...

EF 5 speed manual; PH 4480 Pacemaker Headers; 2 1/2" Lukey Mandrel Bent System; Hi Flow Walker Cat; Stage 3 Crow Cam; ChipTorque Chip; 3" Mandrel Bent Intake; K&N Pod Filter; Low Pedders Suspension; 17" EL GT Champagne Rims; RPM Series Clutch

Top
 Profile  
 
 
 Post subject: Dev 3HL - Exactly what brand/profile???
Posted: Sun May 08, 2005 9:54 am 
Fordmods Newbie
Offline

Age: 44

Posts: 1

Joined: 7th May 2005

Location: Brisbane
QLD, Australia

You guys talk of a dev 3 and dev 3 HL cam... what brand/make/profile are you refering to?

I'm looking at a new cam myself (EF Futura - 5Spd - LSD - Dumped - Genie Custom Extractors -> 2.5")

I'm not looking for a 'hot hot' cam ... but something that'll give me power/torque from 2000/2200RPM -

I'll be upgrading to a new computer shortly after the cam...
(I'm hoping it'll be lumpy enough to stall during idle so that i can convince the wife to get a new Chip ASAP :D )

Suggestions???


Ta
Top
 Profile  
 
 
Posted: Sun May 08, 2005 12:06 pm 
Smokin em up
Offline

Age: 46

Posts: 285

Joined: 6th Nov 2004

Location: x
NSW, Australia

Get the Dev3HL from Jim mock motorsport or neil101 whose car i have seen run on the dyno and it was impressive.

have a look here at JMM site for info

http://www.jimmockmotorsport.com/
Top
 Profile  
 
Display posts from previous:
Sort by  
 Page 2 of 2  [ 21 posts ]  Go to page Previous  1, 2

Who is online

Users browsing this forum: No registered users and 43 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

 

 

It is currently Fri Mar 29, 2024 3:25 am All times are UTC + 11 hours

 

 

(c)2014 Total Web Solutions Australia - Australian Web Hosting and Domain Names