|
| madeaspack |
|
||
|
ive got a 91 ea gl cfi which i have $7000 to spend on!its getting an eb 4lt a 5 speed,custom black interior,racing seats,steering wheel,gearknob,big a*** cam,valve springs,cam gear,chip torque chip,lowered,custom cold air intake and i have put in a 3.9:1 lsd.For the eng and gearbox i have brought a 215000km eb wagon(non smartlock) do i need to change the wiring loom from the ecu to engine bay for the multi point engine or are they same??
any help appreciated 
_________________ 97 el xr6,5 speed short shifter,sequential scoop,no arial,freshly resprayed,low on 17's,3 inch zorst,stainless hi flo cat,snort stage 3 stainless manifold,garrett t04e,front mount cooler,wolf 3d ecu,seimens 760cc injectors,walbro fuel pump |
||
| Top | |
||
| madmax |
|
|||
|
Yes you will need a new loom, as a CFi has only 2 injectors and MPFI with six thus six connectors in loom for injectors. Also various sensors are in differant places, so current loom wont work/reach etc.
_________________
|
|||
| Top | |
|||
| LSD |
|
|||
|
The MPFI 6 cyl engines may have 6 injectors but they're fired in two banks of three meaning you still only have two injector lines coming out of the ECU (Sequential injection wasn't used on sixes prior to the AU afaik). You shouldn't need to replace *all* the wiring between the ECU and the engine, only the parts around the manifold. Even though you're not converting a CFI to MPFI this tutorial may still be able to help you out:
http://www.ford-tech.com/articles.php?articleId=46
_________________ Team Argon Silver |
|||
| Top | |
|||
| madeaspack |
|
||
|
thanks i knew the manifold loom is different but wasnt sure about the ecu to manifold loom.
_________________ 97 el xr6,5 speed short shifter,sequential scoop,no arial,freshly resprayed,low on 17's,3 inch zorst,stainless hi flo cat,snort stage 3 stainless manifold,garrett t04e,front mount cooler,wolf 3d ecu,seimens 760cc injectors,walbro fuel pump |
||
| Top | |
||
| Punnisher_42 |
|
|||
|
LSD wrote: The MPFI 6 cyl engines may have 6 injectors but they're fired in two banks of three meaning you still only have two injector lines coming out of the ECU (Sequential injection wasn't used on sixes prior to the AU afaik). You shouldn't need to replace *all* the wiring between the ECU and the engine, only the parts around the manifold. Even though you're not converting a CFI to MPFI this tutorial may still be able to help you out:
http://www.ford-tech.com/articles.php?articleId=46 If the injectors are fired in banks as you say, then how does it avoid the other 2 injectors squirting fuel in at the wrong time?
_________________ Regards, |
|||
| Top | |
|||
| madeaspack |
|
||
|
ecu controls when the injectors are fired mpfi ecu will fire 3 at a time where a cfi ecu will only fire 1
_________________ 97 el xr6,5 speed short shifter,sequential scoop,no arial,freshly resprayed,low on 17's,3 inch zorst,stainless hi flo cat,snort stage 3 stainless manifold,garrett t04e,front mount cooler,wolf 3d ecu,seimens 760cc injectors,walbro fuel pump |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 62 guests |
