Fordmods Logo

EF Falcon (another) oil leak question 

 

Page 1 of 1 [ 6 posts ] 

 
 Post subject: EF Falcon (another) oil leak question
Posted: Tue Nov 01, 2011 11:03 pm 
Oompa Loompa
Offline
User avatar

Age: 35

Posts: 29

Joined: 20th Aug 2009

Ride: 1996 EF Falcon

Location: Broken Hill
NSW, Australia

Gday

Sorry for another oil leak post, but I have a pr*ck of a leak that's been hitting the belt and flicking sh*t all over the place, for some reason took a while to find out where it was coming from.

Sprayed it with high pressure hose n took it straight home to catch the leak and it had already pooled up..is it a quick and easy fix, or do I have to root around. (referring to attachment)

Attachment:
drip.JPG
drip.JPG [ 21.22 KiB | Viewed 3742 times ]

Here's where it is dripping from.
Notice how much it has pooled up within less than 2minutes =/
Top
 Profile  
 
 
 Post subject: Re: EF Falcon (another) oil leak question
Posted: Tue Nov 01, 2011 11:11 pm 
NSW Cruise Moderator
Offline
User avatar

Age: 46

Posts: 7338

Joined: 5th Nov 2004

Gallery: 12 images

Ride: TE50

Location: ɹǝpun uʍop
NSW, Australia

easy fix, undo bolt enough that it just hangs on the thread, put some silastik under the bolt head, just enough that it will drag it into the hole, do it up again. let it have a chance to go off before driving it again.

 

_________________

Image

I have a car.

Top
 Profile  
 
 
 Post subject: Re: EF Falcon (another) oil leak question
Posted: Tue Nov 01, 2011 11:56 pm 
Oompa Loompa
Offline
User avatar

Age: 35

Posts: 29

Joined: 20th Aug 2009

Ride: 1996 EF Falcon

Location: Broken Hill
NSW, Australia

cheers buddy
I have some silastik gasket gear laying around luckily, pr*ck of a thing, least I'll be able to give it a service without losing any oil.
Top
 Profile  
 
 
 Post subject: Re: EF Falcon (another) oil leak question
Posted: Wed Nov 02, 2011 4:53 pm 
Oompa Loompa
Offline
User avatar

Age: 35

Posts: 29

Joined: 20th Aug 2009

Ride: 1996 EF Falcon

Location: Broken Hill
NSW, Australia

Ok so the silastik didn't work.

Found that its pissing out at the back not the front..
any ideas what would be the easiest way to seal the back up..or am I going to have to McGyver something up.

Im down to the last of my oil and need this fixed before it gets serviced.
Attachment:
File comment: This much p****d out after a couple laps around the block.
2011-11-02 16.00.17.jpg
2011-11-02 16.00.17.jpg [ 466.1 KiB | Viewed 160 times ]

Attachment:
File comment: The back...how the eff shall I do this
2011-11-02 16.00.43.jpg
2011-11-02 16.00.43.jpg [ 374.7 KiB | Viewed 167 times ]
Top
 Profile  
 
 
 Post subject: Re: EF Falcon (another) oil leak question
Posted: Wed Nov 02, 2011 6:20 pm 
Technical Contributor
Offline

Age: 66

Posts: 6815

Joined: 22nd Jun 2005

Gallery: 8 images

Ride: EF Fairmont

Location: Campbelltown
NSW, Australia

Remove your powersteering pump, you don't need to disconnect the hoses, lift it aside, remove the mounting bracket, clean the face on the motor casing, apply blue silicon on the casing, refit mount, use silicon on bolt heads, refit pump and belt. Allow to dry.
Top
 Profile  
 
 
 Post subject: Re: EF Falcon (another) oil leak question
Posted: Thu Nov 03, 2011 10:26 am 
Getting Side Ways
Offline

Posts: 890

Joined: 1st Apr 2005

Gallery: 4 images

Ride: EF XR6 Wagon, AU2 XR6 VCT

Power: 148 rwkw

Location: Auckland
New Zealand

I had a leak from the same place on my EF. Couldn't stop the leak with sealant. Turned out to be a failed O-ring around the chain tensioner oil restrictor - it sits in the front of the block, behind the timing chain cover. The high pressure oil blew through the timing chain cover gasket, found the bolt and forced its way out.

If you can't stop the leak with sealant, this may point you in the right direction. The oil pressure at the timing chain tensioner is more than a sealant can normally hold. If this turns out to be the cause, the timing chain cover needs to come off - not a small job, sorry to say. Hope the sealant does the trick for you.

 

_________________

95 EF XR6 wagon, 17" FTRs, DBA rotors, KYB/Koni, AU bottom end, ported EF head, backcut valves, SS Inductions, Territory intake, 10.2 CR, Auckland 1258 cam, vernier gear, PH4480 headers, no cat, Tickford 2.5", 2800rpm stall, J3 chip

Top
 Profile  
 
Display posts from previous:
Sort by  
 Page 1 of 1  [ 6 posts ] 

Who is online

Users browsing this forum: Convict201011 and 68 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

 

 

It is currently Fri Apr 19, 2024 4:43 pm All times are UTC + 11 hours

 

 

(c)2014 Total Web Solutions Australia - Australian Web Hosting and Domain Names