|
| effalcon94 |
|
||
|
hey guys i have a 94 ef auto and a eb series 1 auto eb wana put the ef trans into the eb will it be a straight sawp? any wires have to be changed?
cheers anthony |
||
| Top | |
||
| jonathon |
|
|||
|
they are the same trans so should be a straight swap over.
cheers
_________________ Owning 1 of 84,847 ebII. |
|||
| Top | |
|||
| effalcon94 |
|
||
|
nice!
coz ive got an au conversion done but my trans wont select 3th gear so i thort it culd be that trans? |
||
| Top | |
||
| frd906n |
|
||
|
did u ask the mech who did the conversion that his loom might have stuffed up the trans wiring
_________________ Daily Driver, Series 1 Au Forte Quote: Posted by Xcabbi, Does it slap or rattle? Rattle is more to do with timing chains and tensioners. Slap is more to do with lifters, rings, bearings or GENIII boat anchors
|
||
| Top | |
||
| effalcon94 |
|
||
|
havnt got a hold of him js yet but i wana know wats hes done wrong
regards anthony |
||
| Top | |
||
| frd906n |
|
||
|
is it stuck in 3rd or it wont go into 3rd
_________________ Daily Driver, Series 1 Au Forte Quote: Posted by Xcabbi, Does it slap or rattle? Rattle is more to do with timing chains and tensioners. Slap is more to do with lifters, rings, bearings or GENIII boat anchors
|
||
| Top | |
||
| effalcon94 |
|
||
|
its goes
1ST then second at 32 then 3rd at 62 then no more changes of gears.. when i have my ef i could drive slow down my street and it wud change at low revs but i have to get to 32kmph to change to second regards anthony |
||
| Top | |
||
| frd906n |
|
||
|
sounds like its in limp home mode
_________________ Daily Driver, Series 1 Au Forte Quote: Posted by Xcabbi, Does it slap or rattle? Rattle is more to do with timing chains and tensioners. Slap is more to do with lifters, rings, bearings or GENIII boat anchors
|
||
| Top | |
||
| effalcon94 |
|
||
|
any idea how to fix it? shuld it change like my ef did? not jst at a certain speed?
regards anthony |
||
| Top | |
||
| frd906n |
|
||
|
just take it back to him and tell him to fix it, if its was working perfectly fine before the condtion,
must be his f**k up
_________________ Daily Driver, Series 1 Au Forte Quote: Posted by Xcabbi, Does it slap or rattle? Rattle is more to do with timing chains and tensioners. Slap is more to do with lifters, rings, bearings or GENIII boat anchors
|
||
| Top | |
||
| alby-73 |
|
||
|
frd906n wrote: just take it back to him and tell him to fix it, if its was working perfectly fine before the condtion, must be his f**k up what computer you running? ef or au? not an electrical guru but some one here might know more than me |
||
| Top | |
||
| effalcon94 |
|
||
|
eb computer
cheers anthony |
||
| Top | |
||
| BenJ |
|
||
|
When you get up to 80 or so does it change into 4th? and does the convertor lock up?
The early computers had s**t auto mapping compared to the EF/EL. Cheers BenJ
_________________ BenJ's EB T5 DOHC Ghia Wagon - Current Ride |
||
| Top | |
||
| effalcon94 |
|
||
|
benj i was doin 140 and was stil in 3rd mate.
whats the converter? i also realised tonite i can just puth on the shifter without pushing the button and it goes into neutral? not normal is it? regards anthony |
||
| Top | |
||
| BenJ |
|
||
|
I think you should be taking it back to the place that did the work, and ask them to rectify the issues.
Cheers BenJ
_________________ BenJ's EB T5 DOHC Ghia Wagon - Current Ride |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 24 guests |
