Fordmods Logo

EL on LPG - replacing H/G with AU one. Shave head as well? 

 

Page 1 of 1 [ 5 posts ] 

 
 Post subject: EL on LPG - replacing H/G with AU one. Shave head as well?
Posted: Sat Nov 06, 2004 1:53 pm 
Getting Side Ways
Offline

Posts: 625

Joined: 6th Nov 2004

Ride: R32 GTR

Location: Brackistan
VIC, Australia

My 4 litre six pot taxi is going to be up for a head gasket replacement soon and I mainly use it on LPG, only on petrol once a week for a few mins to keep the injectors alive.

I'm under the impression the AU gasket is slightly thinner and will increase the static CR too. Since LPG has a considerably higher MON and RON than regular ULP, will the engine benefit from having the head shaved to bring the CR up around 0.3-0.6 ish?

What is the CR increase from merely switching to the AU gasket without modifying anything else?

Naturally I dont want to shave the head excessively which will result in messing up the squish area and combustion chamber, are these problems worth considering when wishing to increase the CR such a small amount?

Lastly, I'm intending on keeping everything else stock - I want to increase the CR mainly to improve fuel economy of the guzzler. Is there any other advice that can be given?

Cheers
Top
 Profile  
 
 
Posted: Sat Nov 06, 2004 10:32 pm 
Smokin em up
Offline

Age: 37

Posts: 204

Joined: 6th Nov 2004

Gallery: 2 images

Ride: EL Futura

Location: Kurri Kurri
NSW, Australia

id say the shave would be well worth it to keep them the same...i dont think there are a lot of diffderences between the two engins tho. If it were me id just put the AU head gasket on it n leave it...

if u get problems maybe shave it but you can always shave it again later but you cant add more to it!
Top
 Profile  
 
 
Posted: Sat Nov 06, 2004 11:25 pm 
Getting Side Ways
Offline
User avatar

Age: 41

Posts: 1037

Joined: 5th Nov 2004

Gallery: 1 images

Ride: V8 T5 Fairmont & BA XR6T

Location: Sydney
NSW, Australia

My oppinion is do it once do it properly. What your symptoms so far as to why you need to change the head gasket? If it is leaking coolant between number 2 & 5 then you will probably need to deck the head again any way to get it true again, they dont take off much when they deck it though. JMM sell these funky dory head gaskets that are 0.020" thinner, and they are about $100

 

_________________

Dima, Mitch & Jay's RPD

Top
 Profile  
 
 
Posted: Sun Nov 07, 2004 4:10 pm 
Fordmods Junkie
Offline
User avatar

Age: 45

Posts: 1000493

Joined: 6th Nov 2004

Gallery: 2 images

Ride: AUXR6 HP With Ducati SupA Bike!

Location: Perth
WA, Australia

yes sahve the head a small amount it will be good forlpg then u may need to run PULP but meh!

make sure you have the head checked
hell while it is out get the ports matched at the same time makea good improvement in flow etc

 

_________________

RIP SCOTT

Top
 Profile  
 
 
Posted: Sun Nov 07, 2004 5:21 pm 
Getting Side Ways
Offline

Posts: 625

Joined: 6th Nov 2004

Ride: R32 GTR

Location: Brackistan
VIC, Australia

Thanks for the replies everyone.

Engine is stock 9:1 compression ratio isn't it?

What is the exact CR increase by doing nothing other than using an AU steel gasket in place of the regular gasket?

What is an ideal CR to increase the engine to, purely for running LPG.

I understand that PULP would be required after the CR increase to prevent detonation, thats fine. The amount of times annually this vehicle sees the petrol tank opened would be easily counted with three fingers and you'd still have a spare :)
Top
 Profile  
 
Display posts from previous:
Sort by  
 Page 1 of 1  [ 5 posts ] 

Who is online

Users browsing this forum: No registered users and 39 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

 

 

It is currently Wed Apr 24, 2024 8:35 pm All times are UTC + 11 hours

 

 

(c)2014 Total Web Solutions Australia - Australian Web Hosting and Domain Names