Fordmods Logo

HELP HOW DO I WIRE UP A 6 CLY BA INGINE FOR A SPEEDWAY CAR 

 

Page 1 of 1 [ 7 posts ] 

 
 Post subject: HELP HOW DO I WIRE UP A 6 CLY BA INGINE FOR A SPEEDWAY CAR
Posted: Sun Apr 15, 2012 1:57 am 
Fordmods Newbie
Offline

Age: 62

Posts: 3

Joined: 5th Apr 2012

Ride: Speedway Car

Location: TEMORA COUNTRY NSW
NSW, Australia

HELP:cry: Hi iam putting in a ba 6cly in my speedway car and does any one know a basic way to wire it up..Do i modifie a standard loom or buy a microtech unit as speedway car only has off on and start button, Ive looked at a standerd loom out of street car but wires going every where???? Any ideas, Hope some one out there can help. Cheers Mark Is there any one that can give me a diagram how to do it as the help would be a big help to me..
Top
 Profile  
 
 
 Post subject: Re: HELP HOW DO I WIRE UP A 6 CLY BA INGINE FOR A SPEEDWAY CAR
Posted: Sun Apr 15, 2012 10:40 am 
Getting Side Ways
Offline

Posts: 5503

Joined: 20th May 2005

Gallery: 11 images

Ride: EB1 Fairmont Ghia T5 Wagon

Location: Seven Hills, Sydney
NSW, Australia

Hi.

You need to build a custom wiring loom to adapt the BA Engine and factory PCM to the vehicle you are putting it in.

This is still a relatively new conversion and there is little available information.

I am in the middle of installing a BA Engine into my EB Wagon street car, and I would have a couple of hundred man hours into it already, most of it research. I will eventually make up a diagram, but it is some time away.

A speedway car would be easier as you don't have to worry about A/C and signals back to the car etc.

Good luck.

BenJ

 

_________________

BenJ's EB T5 DOHC Ghia Wagon - Current Ride
BenJ's EB GL Sedan - Previous Ride
My respect and thanks go to - snap0964, Paulmac, SWC and MRE-50L

Top
 Profile  
 
 
 Post subject: Re: HELP HOW DO I WIRE UP A 6 CLY BA INGINE FOR A SPEEDWAY CAR
Posted: Sun Apr 15, 2012 3:41 pm 
Fordmods Newbie
Offline

Age: 62

Posts: 3

Joined: 5th Apr 2012

Ride: Speedway Car

Location: TEMORA COUNTRY NSW
NSW, Australia

:lol: Thanks any help would be good. Cheers and thanks again for your time in replying to me.
Top
 Profile  
 
 
 Post subject: Re: HELP HOW DO I WIRE UP A 6 CLY BA INGINE FOR A SPEEDWAY CAR
Posted: Sun Apr 15, 2012 9:13 pm 
Getting Side Ways
Offline

Age: 32

Posts: 789

Joined: 9th Dec 2011

Ride: S1 eb 5speed

Location: Coffs Harbour
NSW, Australia

Man oh man,I wonder if you need the full CAN to get it going?
Top
 Profile  
 
 
 Post subject: Re: HELP HOW DO I WIRE UP A 6 CLY BA INGINE FOR A SPEEDWAY CAR
Posted: Sun Apr 15, 2012 9:35 pm 
Getting Side Ways
Offline

Posts: 5503

Joined: 20th May 2005

Gallery: 11 images

Ride: EB1 Fairmont Ghia T5 Wagon

Location: Seven Hills, Sydney
NSW, Australia

Pakrat wrote:
Man oh man,I wonder if you need the full CAN to get it going?


Nope.

You do have to purchase an XCal 3 flash unit to turn all of the security/CAN stuff off in the BA PCM though.

I did forget that bit above.

That alone is $800 odd worth of hard earned dosh.

Cheers
BenJ

 

_________________

BenJ's EB T5 DOHC Ghia Wagon - Current Ride
BenJ's EB GL Sedan - Previous Ride
My respect and thanks go to - snap0964, Paulmac, SWC and MRE-50L

Top
 Profile  
 
 
 Post subject: Re: HELP HOW DO I WIRE UP A 6 CLY BA INGINE FOR A SPEEDWAY CAR
Posted: Sun Apr 15, 2012 9:41 pm 
Moderator
Offline

Posts: 14489

Joined: 7th Nov 2004

Ride: AU XR8

Location: a shit suburb in sydney
NSW, Australia

FAST #41 wrote:
HELP:cry: Hi iam putting in a ba 6cly in my speedway car and does any one know a basic way to wire it up..Do i modifie a standard loom or buy a microtech unit as speedway car only has off on and start button, Ive looked at a standerd loom out of street car but wires going every where???? Any ideas, Hope some one out there can help. Cheers Mark Is there any one that can give me a diagram how to do it as the help would be a big help to me..


being a speedway car, go with the microtech or similar ecu. just keep it basic, crank sensor, water temp, air temp, ls1 coils or coil igniters firing coil on plug..
dont worry about the vct, lock the cams and go for it..
Top
 Profile  
 
 
 Post subject: Re: HELP HOW DO I WIRE UP A 6 CLY BA INGINE FOR A SPEEDWAY CAR
Posted: Sun Apr 15, 2012 10:15 pm 
Getting Side Ways
Offline

Age: 32

Posts: 789

Joined: 9th Dec 2011

Ride: S1 eb 5speed

Location: Coffs Harbour
NSW, Australia

Well that saves a fair headache
Top
 Profile  
 
Display posts from previous:
Sort by  
 Page 1 of 1  [ 7 posts ] 

Who is online

Users browsing this forum: Google [Bot] and 59 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

 

 

It is currently Fri Mar 29, 2024 10:46 pm All times are UTC + 11 hours

 

 

(c)2014 Total Web Solutions Australia - Australian Web Hosting and Domain Names