|
| Shifteh |
|
||
|
I need to get my harmonic balancer off to put new timing kit in , because i cant seem to get timing cover off , looks like balancer is blocking its removeal
_________________ Crank Assembly balanced, HV oil pump, ACL Trimetal bearings, "1 extra oil clearance taking to around 0.0650-0.0700 on mains and big ends, Moly rings,, Xr6 Cam, POD ( Possibly oversize injectors), Block, Head, Timing cover, belt idler, Alternator,painted in ford light blue |
||
| Top | |
||
| nalane |
|
|||
|
Balancer has to come off, get your hands on a harmonic balance puller. Tis the only way.
|
|||
| Top | |
|||
| Shifteh |
|
||
|
i mean the bolt, heads off, do i jam something in someware, jam the old chain ???
_________________ Crank Assembly balanced, HV oil pump, ACL Trimetal bearings, "1 extra oil clearance taking to around 0.0650-0.0700 on mains and big ends, Moly rings,, Xr6 Cam, POD ( Possibly oversize injectors), Block, Head, Timing cover, belt idler, Alternator,painted in ford light blue |
||
| Top | |
||
| nalane |
|
|||
|
I motor is out of car, Jam the flywheel. If in the car put a socket on a breaker bar, jam it on the ground and hit the starter. WARNING. make sure you get all the engine rotation and bar the right way.
|
|||
| Top | |
|||
| tiny56 |
|
||
|
if you try it nalane's way make sure you disable the ignition or fuel system so it cannot start
|
||
| Top | |
||
| finnigan001 |
|
|||
|
Here's some tips in this thread. Also how to go about the crank seal which you may as well do while off.
ford-4l-and-6-cylinder-f1/front-crank-seal-t82615.html
_________________ 1995 EF Futura |
|||
| Top | |
|||
| Shifteh |
|
||
|
thats anouther reason i want to get it off ive got a crank seal in the timing kit i got , and if you read above ,, the " Heads off" so stator motor is not a option, ,
fun fun fun
_________________ Crank Assembly balanced, HV oil pump, ACL Trimetal bearings, "1 extra oil clearance taking to around 0.0650-0.0700 on mains and big ends, Moly rings,, Xr6 Cam, POD ( Possibly oversize injectors), Block, Head, Timing cover, belt idler, Alternator,painted in ford light blue |
||
| Top | |
||
| nalane |
|
|||
|
Your only option is a rattle gun or jam the flywheel through the starter motor opening. This is why you must remove the items in the correct order. You could try screwing two long gigh tensile bolts into the balancer, jam a bar between them to stop the motor spinning. Good chance the bolts will bend. Last resort heat.
|
|||
| Top | |
|||
| Shifteh |
|
||
|
i might jam the old chain up , not like im using again
_________________ Crank Assembly balanced, HV oil pump, ACL Trimetal bearings, "1 extra oil clearance taking to around 0.0650-0.0700 on mains and big ends, Moly rings,, Xr6 Cam, POD ( Possibly oversize injectors), Block, Head, Timing cover, belt idler, Alternator,painted in ford light blue |
||
| Top | |
||
| nalane |
|
|||
|
If you are going to do that, release the chain tensioner, cut the chain and pull it off the crank pully. Then you can do the starter motor trick.
|
|||
| Top | |
|||
| Shifteh |
|
||
|
ok , ill go and have a fiddel
_________________ Crank Assembly balanced, HV oil pump, ACL Trimetal bearings, "1 extra oil clearance taking to around 0.0650-0.0700 on mains and big ends, Moly rings,, Xr6 Cam, POD ( Possibly oversize injectors), Block, Head, Timing cover, belt idler, Alternator,painted in ford light blue |
||
| Top | |
||
| Shifteh |
|
||
|
JUST UNDID HARMONIC BALANCER BOLT WITH MY BARE HANDS ON A X type tyre iron , * Feels tuff*
_________________ Crank Assembly balanced, HV oil pump, ACL Trimetal bearings, "1 extra oil clearance taking to around 0.0650-0.0700 on mains and big ends, Moly rings,, Xr6 Cam, POD ( Possibly oversize injectors), Block, Head, Timing cover, belt idler, Alternator,painted in ford light blue |
||
| Top | |
||
| nalane |
|
|||
|
Good s**t. They can be a pain in the a*** but when you hold your tongue right they fall off.
|
|||
| Top | |
|||
| Shifteh |
|
||
|
*Goes to supercheap to get Harmonic balancer puller for $25
_________________ Crank Assembly balanced, HV oil pump, ACL Trimetal bearings, "1 extra oil clearance taking to around 0.0650-0.0700 on mains and big ends, Moly rings,, Xr6 Cam, POD ( Possibly oversize injectors), Block, Head, Timing cover, belt idler, Alternator,painted in ford light blue |
||
| Top | |
||
| nalane |
|
|||
|
Gota have one, if that comes off by hand you've got a problem.
|
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: Google [Bot], Google Adsense [Bot] and 42 guests |
