Fordmods Logo

How to progaram smartlock remote on a efi6? 

 

Page 1 of 1 [ 3 posts ] 

 
 Post subject: How to progaram smartlock remote on a efi6?
Posted: Sun Mar 18, 2007 10:49 pm 
Stock as a Rock
Offline

Age: 38

Posts: 117

Joined: 3rd May 2006

Location: melbourne
VIC, Australia

Hi guys,

I lost my orginal remote and my spare seems to have not been
Programmed to my car how do you program the remote to the car?

Cheers
Mark.
Top
 Profile  
 
 
Posted: Sun Mar 18, 2007 10:52 pm 
Getting Side Ways
Offline
User avatar

Age: 31

Posts: 1085

Joined: 6th Nov 2004

Ride: BF XR Turbo

Location: Castle Hill
NSW, Australia

its in the technical docos

http://www.fordmods.com/forums/documents.php?doc=26


Adding and Removing remote Keypads to the Smartlock module
Up to four Keypads can be programmed and used with the Smartlock Remote Central locking system.
If you have replaced the BEM, or new keypads are being added to the system, you will need to train the keypad codes to the module.

1. The ignition switch should be in the Off position, with all the doors shut and Unlocked.
2. Turn the ignition key to the ACCESSORY position and within 5 seconds, operates the rear demister switch exactly three times in quick succession. (IE. Press the switch so the Demister light turns on, then off, then back on again.)
3. After the 5 seconds is up, the door locks will change state, to indicate that the BEM has entered keypad learn mode.
NOTE : All existing keypads at this point, have been erased from memory !
4. Press either buttons on the keypad that is to be trained. The door locks will change state twice, to indicate that the keypad has been added to the BEM memory.
5. Follow step 4. for each keypad that is to be added to the BEM memory. A maximum of 4 keypads can be added to the BEM memory.NOTE : You must teach all remote keypads for the Smartlock module, before proceeding.
6. When you have taught all the remote keypads, turn the ignition to the Off position to leave the learn mode. The door locks will change state to indicate a return to normal mode.
7. Check the function of both buttons on each keypad, to ensure that the keypad has been trained.




cheers
mitch

 

_________________

BF XR6T 6spd Auto. 60lb injectors, Hybrid Cooler, Custom Piping, Custom Surge Tank, Actuator.

12.3 @ 114

Top
 Profile  
 
 
Posted: Sun Mar 18, 2007 11:02 pm 
Stock as a Rock
Offline

Age: 38

Posts: 117

Joined: 3rd May 2006

Location: melbourne
VIC, Australia

mitchg911 wrote:
its in the technical docos

http://www.fordmods.com/forums/documents.php?doc=26


Adding and Removing remote Keypads to the Smartlock module
Up to four Keypads can be programmed and used with the Smartlock Remote Central locking system.
If you have replaced the BEM, or new keypads are being added to the system, you will need to train the keypad codes to the module.

1. The ignition switch should be in the Off position, with all the doors shut and Unlocked.
2. Turn the ignition key to the ACCESSORY position and within 5 seconds, operates the rear demister switch exactly three times in quick succession. (IE. Press the switch so the Demister light turns on, then off, then back on again.)
3. After the 5 seconds is up, the door locks will change state, to indicate that the BEM has entered keypad learn mode.
NOTE : All existing keypads at this point, have been erased from memory !
4. Press either buttons on the keypad that is to be trained. The door locks will change state twice, to indicate that the keypad has been added to the BEM memory.
5. Follow step 4. for each keypad that is to be added to the BEM memory. A maximum of 4 keypads can be added to the BEM memory.NOTE : You must teach all remote keypads for the Smartlock module, before proceeding.
6. When you have taught all the remote keypads, turn the ignition to the Off position to leave the learn mode. The door locks will change state to indicate a return to normal mode.
7. Check the function of both buttons on each keypad, to ensure that the keypad has been trained.

Thanks mitch for ya help mate!!!!


cheers
mitch
Top
 Profile  
 
Display posts from previous:
Sort by  
 Page 1 of 1  [ 3 posts ] 

Who is online

Users browsing this forum: Google [Bot] and 21 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

 

 

It is currently Sat Dec 16, 2017 1:16 am All times are UTC + 11 hours

 

 

(c)2014 Total Web Solutions Australia - Australian Web Hosting and Domain Names