|
| justindude880 |
|
||
|
 i was just wantin to know if anyone would be abil to tell me how to remove the rear windscreen and the rear quarter windows in a ef ford any help would be greatfull
|
||
| Top | |
||
| efbignik |
|
|||
|
with a hammer dude
sorry but can't give you any thing better
_________________ EFBIGNIK 145.9 RWKW Falcon / 16.27 @ 86.72mph (Stock)
|
|||
| Top | |
|||
| Falcs |
|
|||
|
I got told at a panel beaters that if you take out the back window you have to replace it with a new one because it can't be done without damaging it. I reckon they where full of it but... but i donno.. can anyone confirm this?
_________________ -------- Falcs -------- |
|||
| Top | |
|||
| snikers00 |
|
|||
|
If you are going to take out the back windscreen you might aswell break it unless you can cut the glue and keep the seal in tact. Because there are no genuine or aftermarket seals available. The new windscreens come with them already attached.
If you remove the interior trims around the window its easy to get to the glue with a good flexible knife. As for the rear quarters, theyre just glued on all the way around on two rubber tabs holding them in the door at the bottom. |
|||
| Top | |
|||
| Sikef6 |
|
||
|
windscreens obrien or similar. Cost is reasonable tippin around 80 bucks to remove the lot. They use a special cutter to slice the glue. can be done with a stanley knife... but you wouldn't, just one of those jobs.
_________________ Back 2 square 1.... |
||
| Top | |
||
| TFI |
|
||
|
I'd have to agree with the hammer method. Quickest and easiest.
_________________ EF Futura - EL GT Snorkle, Alpine Head Unit, 17" CSA Avenger rims, Ford foot mats. |
||
| Top | |
||
| Sturmovik |
|
|||
|
I took out the 1/4 windows with a reasonably flexible serrated kitchen knife. It worked best out of everything else I tried, but it was still a pain in the bum.
_________________ 1993 ED XR6 5speed Polynesian Green. Project car. |
|||
| Top | |
|||
| MARK.TANIA |
|
||
|
IT is true about taking them out . the same as the back window once out you have to get new ones .i work at a panel shop . we have done alot of them and the window guy puts new ones in iasked about it an he said that it is the mould thay use in fatory thay have tryed to put old ones back in . but thay leek .and i have seen them do at least 150 or more
|
||
| Top | |
||
| kapul |
|
|||
|
wat about for an xd ute rear window? I realy need to get it out so i can weld a new roof top skin on... is the only way to get that one out to smash it as well?
_________________ Fact: Chuck Norris is so fast he can run around the world and hit himself in the back of the head
|
|||
| Top | |
|||
| nlbxr6 |
|
|||
|
I run a big panel shop in brisbane the ef rear a good fitter such as obrien or national will charge about 130to remove & replace the qtr glass in the back doors are about 70 each but 8/10 times the qtr glass will break as for the ute they will also do for around 130 out & in unless you have done this type of thing before you will break em the reason most people replace the rear on an ef is because they are what we call encaptulated which means the mould is made as part of the glass 90% of new cars are now like this hope this helps
www.shipstone.com.au winner large panel shop qld paint & panel magazine 2004 2006
_________________ efII wgn xr front xr ecu 17s filter pacemakers highflow cat & 2.5 manual conversion
|
|||
| Top | |
|||
| justindude880 |
|
||
|
i have now found out from experince ie doing it the easy way to get quarter windows out with out shattering is run a stanly knife along the outside of the bottom quarter glass and cut the stay pins and then slowly leaver out from bottom and it will come out easy about 2min all up to remove easy
 
|
||
| Top | |
||
| justindude880 |
|
||
|
i mean between the door skin and the rubber at the outside bottom ohhh and i forgot to tell you all you can reuse them aswell save around $140 per side new
|
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 49 guests |
