|
| Xflow |
|
|||
Age: 36 Posts: 721 Joined: 31st Dec 2005 Ride: EF V8 Futura, 180sx Location: Brisbane, Burpengary |
Hey guys i got to do my front crank seal it squirting all my expensive oil out there ive got the harmonic balancer remover on the harmonic balancer and ive tighten very tight and it hasent even budged ive sprayed INOX on it was well
ANY TRICKS OR THINGS TO WATCH OUT 4? THX
_________________ Ford EF Futura Black
|
|||
| Top | |
|||
| Xflow |
|
|||
Age: 36 Posts: 721 Joined: 31st Dec 2005 Ride: EF V8 Futura, 180sx Location: Brisbane, Burpengary |
bright one aint i
It a EF FAIRMONT 4.0L
_________________ Ford EF Futura Black
|
|||
| Top | |
|||
| Krytox |
|
|||
|
breaker bar and some elbow grease.
Or the aussie way... impact socket, breakerbar, steel tube and concrete floor. *fingers crossed* hit the key! I strongly recommend not to use the aussie way!
_________________ Carefree, we may not be number one, but we're up there. |
|||
| Top | |
|||
| Krytox |
|
|||
|
ohh, i'll read better next time.... the bolts out i take it!
_________________ Carefree, we may not be number one, but we're up there. |
|||
| Top | |
|||
| fordster |
|
|||
|
takeing the nut out is the hardest part!!
Ive just done it took two people screwdriver through balancer onto timeing case . And cross fingers u dont damage case bolt on mine was real b**ch took 30 mins before it finaly came off
_________________ EF POWERED EA |
|||
| Top | |
|||
| madmax |
|
|||
|
Did you take the radiator out? This will give you more room to work with.
Use a large breaker bar with impact socket. Wedge breaker bar against sub frame. Remove Starter relay. Jumper starter relay to nudge engine to turn over. (far more control than using the key, plus you are in a better position to see whats happening.)
_________________
|
|||
| Top | |
|||
| Xflow |
|
|||
Age: 36 Posts: 721 Joined: 31st Dec 2005 Ride: EF V8 Futura, 180sx Location: Brisbane, Burpengary |
LOL removing the bolt was easy as using 2 fingers lol
it was finger tight bit of a worry who ever the mechanic was that worked on the car. i have removed the starter relay. I just put the coolant into my motor on sunday and i was it my mate when i was putting it in i bet ya with in a week ill have to remove the radiator and would u look at that i must be able to see the futura LOL ill remove it now and ill try 2 swrew drivers then
_________________ Ford EF Futura Black
|
|||
| Top | |
|||
| Xflow |
|
|||
Age: 36 Posts: 721 Joined: 31st Dec 2005 Ride: EF V8 Futura, 180sx Location: Brisbane, Burpengary |
good new every one the darn thing is off i used the harmonic balancer puller and a pry bar and it cam off easy after i crushed the sensor lol
but it off and i didn't even have to remove the radiator thank god. i used a sheet of tin to cover the radiator and it worked like a charm now just having a little problem of removing that darn seal. it sitting there rock hard lol
_________________ Ford EF Futura Black
|
|||
| Top | |
|||
| LUMO |
|
|||
|
no yuo guys killing yourselves go to super cheap and they have pulling that a made to take off you balancer its like 20 to 40 buks its the best investment for your car hell of alot easier go there and ask them for a pully to take off your balancer it clamps to your balancer and with your socket your pull it out it mad
_________________
|
|||
| Top | |
|||
| aaron_hogan |
|
||
|
Don't use the "two screwdrivers" trick. I've seen people puncture their timing covers prying them off.
Best thing to do in my experience is to use a proper puller AND a rattle gun to drive it. For some reason when just using a ratchet the balancers often won't budge. Using a rattle gun draws up the tension in a linear and progressive way such that it seems to break the seal easier. I once resorted to (made the mistake of) using a large 2 jaw external gear puller. Popped the external ring right off the balancer! Didn't matter at that point i just wanted it off there. When putting it back use a smear of anti-seize, NOT GREASE, so that the next time it will come off without tears and swearing.
_________________ EA SVO Fairmont Ghia - Recaros, Bilsteins, Sunroof, SVO rims and body kit, Genie headers, DBA rotors. T5 steeda triax short shifter. 3.27 lsd. (EL 4.0 ported/polished, rebuilt and balanced, Dev5 cam. J3 chipped EL ecu, AU injectors). |
||
| Top | |
||
| LUMO |
|
|||
|
yea i used a 3 jaw and itsa great i used a racket tho dont have a rattle gun
_________________
|
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: Google Adsense [Bot] and 67 guests |
