|
| tycron |
|
||
|
Both with angle eyes low beam with projector and hid kit. The 7projector one does look unique
|
||
| Top | |
||
| Mitch_ |
|
|||
Posts: 6168 Joined: 5th Nov 2004 |
i woudlnt put a hid kit in the high beam - you'll essentually loose the ability to flash with them - and bi-xenons should do the job easily
_________________
|
|||
| Top | |
|||
| MAD |
|
|||
|
Mitch_ wrote: i woudlnt put a hid kit in the high beam - you'll essentually loose the ability to flash with them - and bi-xenons should do the job easily Agreed. Keep the halogen high beam for flashability during the day, and at night the BiXenon will light up the road like you've never seen before. My FX-R retrofit turns night into day with highbeam. |
|||
| Top | |
|||
| my671fordv8 |
|
|||
|
tycron wrote: Both with angle eyes low beam with projector and hid kit. The 7projector one does look unique Ok . The mini H1 bixenon high/low kit is $270 from the retrofit source for a pair of projectors.2 sets of projectors are $540 plus $100 to fit them to your lights . As stated before if you have a proper bixenon projector kit you will very rarely need any extra light . Your standard high beams will do fine but the final decision is up to you |
|||
| Top | |
|||
| Eb cruiza |
|
||
|
can u do the same headlight setup for a eb?
|
||
| Top | |
||
| my671fordv8 |
|
|||
|
Eb cruiza wrote: can u do the same headlight setup for a eb? I can put the projectors in your lights but you will need to check out MADs el hid project and wait for him to make the clear lenses for the EB |
|||
| Top | |
|||
| jack3643 |
|
||
|
Anyone got these yet, and if so, how are they? Very interested...
|
||
| Top | |
||
| Kenay |
|
|||
|
i made my own setup ... head over to AFF in b-series section my build thread is in there
|
|||
| Top | |
|||
| my671fordv8 |
|
|||||||
|
jack3643 wrote: Anyone got these yet, and if so, how are they? Very interested... Here are a few i have done. The ba ones are mini H1 projectors . They are the easiest to fit , you remove the globe and the projector plugs into your globe socket . The AU set are a much better projector but cant be installed without cutting or modifying the reflector or headlight housing. The other pic is the light output on low beam.The ba projectors can be ordered with larger shrouds than the ones in the pic . I will never go back to halogens
|
|||||||
| Top | |
|||||||
| jack3643 |
|
||
|
Thanks for the replies guys...
|
||
| Top | |
||
| rustyeb1991 |
|
||
|
can these be done for ed xr6
|
||
| Top | |
||
| TimmyA |
|
|||
|
rustyeb1991 wrote: can these be done for ed xr6 I too am curious if something can be done with the ED XR lamps... replace the old projectors to new ones... I have seen some where you use a stand HID bulb but the projector itself cuts the top off the beam on low and when you go high something in the projector changes and gives you a full beam... The pics on ebay looked good... But I don't enough about all these to justify buying something and then trying to get my lamps apart... If the low beam lamps could be changed to hi/lo lamps that'd be great... Cheers, Tim
_________________ 93 Red ED 5spd Manual Build Thread |
|||
| Top | |
|||
| my671fordv8 |
|
|||
|
TimmyA wrote: rustyeb1991 wrote: can these be done for ed xr6 I too am curious if something can be done with the ED XR lamps... replace the old projectors to new ones... I have seen some where you use a stand HID bulb but the projector itself cuts the top off the beam on low and when you go high something in the projector changes and gives you a full beam... The pics on ebay looked good... But I don't enough about all these to justify buying something and then trying to get my lamps apart... If the low beam lamps could be changed to hi/lo lamps that'd be great... Cheers, Tim Im sure these can be done but dont have any experience with them . However the mini H1 projectors and fxr projectors are both high/low projectors |
|||
| Top | |
|||
| TimmyA |
|
|||
|
Cool...
So what does it take to get someone who knows what they're doing to have a go? Getting alignments and that right... And I'm not entirely sure how you get them apart... The glass looks to be epoxied to the plastic part... Something really hard... And I wasn't prepared to try (it'd be my luck I'd destroy an expensive lamp)... Cheers, Tim
_________________ 93 Red ED 5spd Manual Build Thread |
|||
| Top | |
|||
| rustyeb1991 |
|
||
|
anyone got a broken xr6 projector to donate to the cause?
pleeeease |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: Google Adsense [Bot] and 60 guests |
