|
| JOSE |
|
|||||
|
Behold!
_________________ Because i can. |
|||||
| Top | |
|||||
| TwinturboBMX |
|
|||
|
i love what you did the the ED grill mate. I would do that but its not worth it as i'm getting rid of the grille in about 1 weeks time.
But it looks pretty darn good. What did you use to fasten it all down etc? And howd you do the ED grille?
_________________ 17" Tezza Steelies, King F**king lows, pedders sports ryders, 2.5" cat back exhaust, pacemaker extractors, T5 manual
|
|||
| Top | |
|||
| EFFalcon |
|
|||
|
looks really good
_________________ FALCN6 - EF GLi Turbo, 20" Rims, Air Bag Suspension, Straight LPG, 225rwkw |
|||
| Top | |
|||
| JOSE |
|
|||
|
Its all held on with cable ties (drill i little hole in the plastic and feed it through and around the mesh).
ED grill was done by pulling it apart (its made of 3 peices) discarding the centre bar bit, trimming the back of the funnel, wrapping the mesh over it, re assembling, and cable tieing (to hold the funnel in) badge is held in by its tabs, and a screw into the back. all done for approximately $26
_________________ Because i can. |
|||
| Top | |
|||
| nicco |
|
|||
|
so that mesh is just held on with cable ties down on the EF bit? that sounds too good to be true!!
might be nearing time for my first exterior mod!! 
Last edited by nicco on Sat Jul 30, 2005 2:33 pm, edited 2 times in total. |
|||
| Top | |
|||
| Interceptor |
|
||
|
loks pretty good! did you use any silastic as well as the cable ties?
_________________ Banned |
||
| Top | |
||
| JOSE |
|
|||
|
nah, just cable ties, i did it all without removing the front bar - if id removed it i would have bent the edges of the mesh over and used selastic.
_________________ Because i can. |
|||
| Top | |
|||
| Rick_Deckard |
|
|||
|
You know the Ford logo looks slighty misaligned.
-briskly runs away-
_________________ E39 523i |
|||
| Top | |
|||
| JOSE |
|
|||
|
Till_Lind wrote: You know the Ford logo looks slighty misaligned.
-briskly runs away- Lol, i was waiting for it though, its slightly low off to one side and slightly crooked.
_________________ Because i can. |
|||
| Top | |
|||
| 1 SLY 97EL |
|
|||
|
Makes it look like an early 90's Mustang.
_________________ " In life their is never an Obligation just an Opportunity to..Own an awesome 1970 Ford Mach 1 Mustang! " |
|||
| Top | |
|||
| JOSE |
|
|||
|
what? the poor build quality?
_________________ Because i can. |
|||
| Top | |
|||
| HTCURRY |
|
||
|
JOSE wrote: Till_Lind wrote: You know the Ford logo looks slighty misaligned. -briskly runs away- Lol, i was waiting for it though, its slightly low off to one side and slightly crooked. Jose....u should have used the camera wasnt straight line
_________________ A$1 = Tk 60 = I cant believe how much money im saving! |
||
| Top | |
||
| Rick_Deckard |
|
|||
|
JOSE wrote: Till_Lind wrote: You know the Ford logo looks slighty misaligned. -briskly runs away- Lol, i was waiting for it though, its slightly low off to one side and slightly crooked. Still looks sweet mate. I know if I was to centre that badge on a mesh piece that big, it would look bad. How is it attached?
_________________ E39 523i |
|||
| Top | |
|||
| JOSE |
|
|||
|
JOSE wrote: badge is held in by its tabs, and a screw into the back.
_________________ Because i can. |
|||
| Top | |
|||
| Rick_Deckard |
|
|||
|
JOSE wrote: JOSE wrote: badge is held in by its tabs, and a screw into the back. O right, I did read that, but forgot it instantly, lol.
_________________ E39 523i |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 21 guests |
