|
| Lay3d_low |
|
|||
|
just wana know if i can put mont trims in a gli and cut small hole for the window winder...or will it hit the door handle?
just looking for easy option before i go an spend money on power window setup.,.. any tips, advice, help, anything would be helpfull cheers
_________________ Sexy Xe |
|||
| Top | |
|||
| Freak6 |
|
|||
|
you can get power window motors for around 30 bucks second hand then you just need the wiring and switches.
its pretty easy to do the conversion, i did my full power window conversion in about 5 hour.
_________________ Ford Motor Company
|
|||
| Top | |
|||
| Lay3d_low |
|
|||
|
yeh, just wana know if its possible before i go spend the money...
i also gotta find out how and where to hook things up etc
_________________ Sexy Xe |
|||
| Top | |
|||
| GTO13F |
|
||
|
am thinking of going rear power window's wat the set up cost u?
not that i mind if there not...i dont sit in the back..lol
_________________ EF futura in the build.
|
||
| Top | |
||
| Freak6 |
|
|||
|
ill have a look at where things line up tomorrow night and get back to ya.
i recon its been done before.
_________________ Ford Motor Company
|
|||
| Top | |
|||
| Lay3d_low |
|
|||
|
yeh its been done before i spoke to a guy the other night and thats where igot the power window idea...
yeh cheers mate, will be a good project for the old falcon
_________________ Sexy Xe |
|||
| Top | |
|||
| Lay3d_low |
|
|||
|
can anyone give me a collective cost on parts that ill havta to buy to install windows...and waht i gotta buy to make it all work...
_________________ Sexy Xe |
|||
| Top | |
|||
| low ghia |
|
|||
|
should have bought a ghia in the first place you tight bastard...
LOL...
_________________
|
|||
| Top | |
|||
| Lay3d_low |
|
|||
|
why buy a mont when i got a GLi with Xr spec?
the only thing it didnt come with is the mont seats, power windows and door trims
_________________ Sexy Xe |
|||
| Top | |
|||
| asizzy |
|
||
|
Hi Mate, I did the full power window Conversion on my car recently. Dont know if you know this but theres a Tech Docu on Power Window Conversion: http://www.fordmods.com/forums/Power-Wi ... n-d21.html
Hope this helps. Its has everything youll need to do the conversion. PM me if you got any questions. I think it cost me to do all this about....i think i got lucky with the parts 
_________________ AsIzZy |
||
| Top | |
||
| Lay3d_low |
|
|||
|
oh sweet, ill hava good look at that post
yeh thanks heaps mate
_________________ Sexy Xe |
|||
| Top | |
|||
| SLO247 |
|
||
|
The tech doco is quite good.
If you have a GLi, id suggest... -4 Fairmont Door trims obviously, Could swap front top sections to loose the ghia badges, could swap GLi fabric trim panels on, would have to retrim rears with fabric off fronts perhaps to loose winder hole, or just use front section if it fits. Would be a nice touch to keep it matching. -Centre Console Switch panel, plug and some wire. -Door looms will make it easier, not sure if they plug up to a GLi body loom. -Futura BEM, to allow the power window operation delay etc. -4 Regs obviously, new aftermaket ones are on ebay for about 55 dollars, not sure on quality though. Basically a matter of bolting/wiring it all up, you will have extra to add unless you add fairmont/futura looms. Not sure of futura looms allow for rear windows in the rear doors, through the body loom and between the BEM, windows etc. Hope that helps! |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 32 guests |
