as far as the standard manifold goes im not sure how it will sit on it, if it has a flat face up on the top where the bolt holes are then it wont be a problem, but it will definitely fit the extractors...

have a look at the pics and youll see there is a close up of the very front of it, showing how the angle is mounted, using the exhaust head bolts(which you cant see cos its hidden)it sits on the outside face of the flat plate of the extractors.

note: it is NOT sandwiched between the head and the extractors.

also to anyone who is on the list with pacemaker ph4400's (the weird looking ones!) i need a measurement for them, from the head to the outmost pipe so the heat shield can clear them, or if anyone is local to me ill come and measure them up, anyone in sydney near liverpool? that would be ideal...

cheers

How would you fit these on the extractors? Would you have to drill into the headers?

I have the Pacemaker competitions, are they the weird ones your talking about? If so, what do you need measured on them?

1. voxace
2. Mr_Soul x 2
3. DRHEMI
4. au man
5. lukesghia
6. dasmq x 2
7. bucko
8. twr7cx
9. Vulture
10. Blazing EF
11. ausdealer
12. jet111
13. Pulco

ok, pulco will be the last person to join the list, i needed multiples of 15 and it doesnt look like getting to 30...
and at this point im assuming all people on the list are 100% commited
if more people are interested ill do another group buy later on in the year..

doofus wrote:

ok to install it all you need to is, loosen the exhaust head holts about 2-3mm, then slide the piece of angle into position ( the angle has notches in it and not holes) so it just slips into place. then you just re tighten the bolts. then you bolt the heat shield to the angle, ( stainless steel nuts will be welded to the underside of the angle, and the screws will be supplied - 8mm high tensile stainless steel screws, all good stuff!) it will take you 2 minutes to fit...

twr7cx wrote:



yeah they are it, i need a dimension from the side of the head (the flat face where the exhaust bolts are) to the outer most point of the furthest protruding pipe... my dimension is about 185mm

and as a double check, my furthest pipe is 100mm from the side wall of the engine bay...

if you could get me both of those dimensions that would be great!
if ur not sure what im after ill send you a sketch or a marked up photo

once i have these dimensions ill make a new template to suite both ba and e series.

then ill be looking for peoples names and addresses and model of car, and ill need payments so i can start ordering material, all of which is on hold for me...

and as promised ill give my details to a moderator

cheers

I;ll measure it tonight.

Oh right, i understand now. Thanks for that. Well, when the next group comes along, ill add myself to that!

FYI I am still in as if they dont fit my std set up I will just wait till i get the pacemakers

Just measured and the furthest pipe on the Pacey Comps extends just over 200mm from where the extractors bolt onto the head.

thanks for that, i should only have to extend it by 15mm, but what ill do is ill make a 1:1 drawing of the side on profile and send it to you to make a quick card board template to see that it 100% clears your pipes, ill try send it tonight some time

id rather be safe than sorry!

thanks

no worries.

I'd be up for one depending on the cost, can you make the pics a bit bigger please?
thanks

Costs is in previous posts.

twr7cx: how did it go?

doofus, felony:
if u guys want to start a second list, go for it. just that i need another 12 people before i order the material, so it remains tentative until then, or if its close to the number im sure we can work something out, slightly dearer... you have another week or so

picks are bigger in my gallery, they are all there...

ok, the time has come.
im going to start organising the payments from you guys.

1. voxace
2. Mr_Soul x 2
3. DRHEMI
4. au man
5. lukesghia
6. dasmq x 2
7. bucko
8. twr7cx
9. Vulture
10. Blazing EF
11. ausdealer
12. jet111
13. Pulco



can you all pm me, letting me know your postal address(unless you want to pick it up), model of car and preffered payment method. and ill fix you up with bank details or my address.

Cost is $120
and postage fee will be C.O.D.

i have given all my details to happy moderator as i said. and he has given me the thumbs up to go ahead.

once i have all of the payments i will order the matereial, which i currently have on hold for me.

it should take 1-2 weeks from when i get the material

thanks