Fordmods Logo

FS [VIC]: ~~ ELECTRONIC MAP SENSOR FIX ~~ 

 

Page 1 of 1 [ 6 posts ] 

 
 Post subject: ~~ ELECTRONIC MAP SENSOR FIX ~~
Posted: Mon Apr 12, 2010 7:54 pm 
Fordmods Newbie
Offline

Age: 32

Posts: 0

Joined: 21st Mar 2005

Ride: EA S PACK

Location: RINGWOOD NORTH
VIC, Australia

MAP Sensor Fix

Application

All E-series Map Sensors where more than 9-10psi is going to be run

What does it do
Allows you to run higher boost levels without the MAP sensor stopping you
Allows J3 chip (if pressent) to see 0psi and 5psi points

How does it work
Bleeds off the BOOST ONLY Reference to the map sensor
My System if Electronic so all Vacuum Psi is read as normal and allows map sensor to read 5psi and thats it....from there the system bleeds off boost sense so map sensor never sees more than 5psi of boost

Tested
Sure is...dyno proven to work...and hours and hours of daily driven success...i ran 11-12psi (weather dependant) without the system being anywhere near full potential

What else makes it special
You can adjust MAX ALLOWED BOOST LEVEL...what psi before system starts to work
AND
You can adjust BLEED LEVELS....how much boost is directed away from MAP Sensor
In my case i bleed 100% so no matter what map sensor would see 5psi and the only ever see 5psi for rest of boost increase (11-12psi)

Whats Included
- Boost Sensor
- Bleed Valve & Boost Controller
- All TURBOSMART vac lines (enough vac line to connect from all eseries manifolds to factory map sensor location & to all other components)
- Wiring
- Everything required to plug and play the system

It will be fully assembled for you and will include installation instructions/pics.
I will be contactable for any other questions as well
This system is my design using off the shelf products

to give you an idea
HOW TO INSTALL
- Unplug and remove old vac line between manifold & map sensor
- mount sensor & boost controller somewhere near map sensor
- plug big vac line onto manifolds nipple (where you removed the vac line at step1)
- plug little vac line onto MAP sensor nipple (where you removed the vac line at step1)
- plug little BLACK vac line into a t-piece inline with your factory fuel regulator so it gets the best vac signal
- Soldier wire with no markings to GROUND
- Soldier wire with white marking to a 12v Fuse Protected Circuit (0.5A fuse is heaps)

Start car and your off and working

Kit is adjusted currently for 5psi Turn on and Bleed at 100%.....so map sensor will never see more than 5psi boost
Kit is currently setup for EF/EL BBM....if you run a EA-ED manifold i have included a longer vac line for you to use

PRICE = $150 inc AUS WIDE Shipping

Please feel free to contact me
Brad


PICS
Image
Image
Image
Image
Image
Image
Image

 

_________________

EA Series2 SPAK - GT Body kit, AU3 4.0L, Snort Stage 3 Turbo Kit, Wade AU390 Cam, Bosch 040, Vortech Reg, EL ecu, BBM & J3 Chip, Crane Cams LX91, 3.45LSD, EF T5, Quickshifter, BA knob, Gt bootie, EL Ghia Trims, Racing Seats & Harnesses, 18" Cobra Rims..

259.3rwkw@11psi

Last edited by BJSPENCER85 on Fri May 14, 2010 10:24 pm, edited 2 times in total.

Top
 Profile  
 
 
 Post subject: Re: FS [VIC]: ~~ ELECTRONIC MAP SENSOR FIX ~~
Posted: Mon Apr 26, 2010 8:09 pm 
Fordmods Newbie
Offline

Age: 32

Posts: 0

Joined: 21st Mar 2005

Ride: EA S PACK

Location: RINGWOOD NORTH
VIC, Australia

PRICE NOW

$200

Including FREE Shipping with Insurrance Australia Wide

Thanks
Brad

 

_________________

EA Series2 SPAK - GT Body kit, AU3 4.0L, Snort Stage 3 Turbo Kit, Wade AU390 Cam, Bosch 040, Vortech Reg, EL ecu, BBM & J3 Chip, Crane Cams LX91, 3.45LSD, EF T5, Quickshifter, BA knob, Gt bootie, EL Ghia Trims, Racing Seats & Harnesses, 18" Cobra Rims..

259.3rwkw@11psi

Top
 Profile  
 
 
 Post subject: Re: FS [VIC]: ~~ ELECTRONIC MAP SENSOR FIX ~~
Posted: Fri May 14, 2010 10:24 pm 
Fordmods Newbie
Offline

Age: 32

Posts: 0

Joined: 21st Mar 2005

Ride: EA S PACK

Location: RINGWOOD NORTH
VIC, Australia

Price now $150 with free shipping Aus wide

Thanks
Brad

 

_________________

EA Series2 SPAK - GT Body kit, AU3 4.0L, Snort Stage 3 Turbo Kit, Wade AU390 Cam, Bosch 040, Vortech Reg, EL ecu, BBM & J3 Chip, Crane Cams LX91, 3.45LSD, EF T5, Quickshifter, BA knob, Gt bootie, EL Ghia Trims, Racing Seats & Harnesses, 18" Cobra Rims..

259.3rwkw@11psi

Top
 Profile  
 
 
 Post subject: Re: FS [VIC]: ~~ ELECTRONIC MAP SENSOR FIX ~~
Posted: Sun May 16, 2010 4:53 pm 
Oompa Loompa
Offline

Age: 43

Posts: 32

Joined: 11th Jan 2006

Ride: XE S-Pack

Location: Ballarat
VIC, Australia

Are you going to be making these up as kits and selling them to members, or is this a one-off? If so...would you be prepared to write up a tutorial on how to build these...along with a parts-list...and approximate cost of parts? I'd be interested in doing one of these later on...as my EA Ghia is nowhere near ready for boost yet!
Cheers!
Kev.
spuddly2003@yahoo.com.au

 

_________________

Fords F**kn Rule!!!

Top
 Profile  
 
 
 Post subject: Re: FS [VIC]: ~~ ELECTRONIC MAP SENSOR FIX ~~
Posted: Sun May 16, 2010 8:57 pm 
Fordmods Newbie
Offline

Age: 32

Posts: 0

Joined: 21st Mar 2005

Ride: EA S PACK

Location: RINGWOOD NORTH
VIC, Australia

this is a one off.
my design using off the shelf products.

once this kit sells then yes i will make a how to....but not until this one sells.

thanks
brad

 

_________________

EA Series2 SPAK - GT Body kit, AU3 4.0L, Snort Stage 3 Turbo Kit, Wade AU390 Cam, Bosch 040, Vortech Reg, EL ecu, BBM & J3 Chip, Crane Cams LX91, 3.45LSD, EF T5, Quickshifter, BA knob, Gt bootie, EL Ghia Trims, Racing Seats & Harnesses, 18" Cobra Rims..

259.3rwkw@11psi

Top
 Profile  
 
 
 Post subject: Re: FS [VIC]: ~~ ELECTRONIC MAP SENSOR FIX ~~
Posted: Mon Jun 07, 2010 6:38 pm 
Fordmods Newbie
Offline

Age: 32

Posts: 0

Joined: 21st Mar 2005

Ride: EA S PACK

Location: RINGWOOD NORTH
VIC, Australia

ITEM going back into car....plans have changed and a new project begins which will require this

Admins can now delete thread

Thanks
Brad

 

_________________

EA Series2 SPAK - GT Body kit, AU3 4.0L, Snort Stage 3 Turbo Kit, Wade AU390 Cam, Bosch 040, Vortech Reg, EL ecu, BBM & J3 Chip, Crane Cams LX91, 3.45LSD, EF T5, Quickshifter, BA knob, Gt bootie, EL Ghia Trims, Racing Seats & Harnesses, 18" Cobra Rims..

259.3rwkw@11psi

Top
 Profile  
 
Display posts from previous:
Sort by  
 Page 1 of 1  [ 6 posts ] 

Who is online

Users browsing this forum: No registered users and 10 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

 

 

It is currently Tue Dec 12, 2017 12:55 am All times are UTC + 11 hours

 

 

(c)2014 Total Web Solutions Australia - Australian Web Hosting and Domain Names