Expressions of Interest, until this coming friday when it may be sold pending if
my new setup comes about.

I removed this turbo from my BA XR6 as it was just starting to sound dry on the bearings and when
I returned from work it didnt make boost, but wait, nearly had completely removed it when
I noticed the hose from the intercooler had come off.
So while I have it off the car I may as well do my intended upgrade of larger turbo.

The impellor spins but sounds like the bearings may have dirt in them, shaft play still
feels good and there is no scoring of housing.
I would suggest to have new bearings fitted just to be 100% safe.
It is to be sold with the stainless factory manifold as well I also have a brand new
adjustable 15psi Actuator to go with it.

I have heard Ford charge over $4000 for these turbo's
I will be looking at best offer over $800 for the lot.
PM offers of the lot or each piece.
If postage required it will be very costly due to size and weight.
Please dont make any offers if you arn't prepared to purchase or havn't
the funds to do so.

I am waiting on some replies for my new setup and cant sell it till they are finalised
as may need to refit it if not happy with the replies.

Can be viewed after 7pm

Bump

Are you still going to retain the oil and water feed/return lines with your new turbo? Also, will you be keeping the stock exhaust manifold and heat shielding?

Still havn't got answers at present but so far what I'm looking at
will be a new turbo and manifold and dump pipe.

I will be using new oil feed line but may be retaining the other lines
at this point.

So all up the Turbo, manifold, heat sheilds and oil feedline will all
be up for best offers.

Incase people may not know, I have advertised in the for sale section
Factory BA Turbo Crossover, Pipes, Hoses and Intercooler.
The Lot for these are $140

Also I will be looking at selling my X-Force Stainless 3.5" with Seperate
outlet Wastegate pipe.
And turbo to airbox plazmaman pipe and hose setup.
This is the drivers side setup that requires either plazmaman air box
or similar with either battery relocated or run like the plazmaman
setup which uses a Oddessey battery inside the airbox as well a pod filter.
The pipe has 2 outley fittings on it one for blowoff valve plumb back and the
other for engine back pressure releif.

$300 For the Xforce Dump pipe
$100 For the Plazmaman Turbo to airbox Intake pipe.

All this gear will nearly have you a full Turbo setup.

With everything here I was making well over 275rwkw.
My BA ran 13.33s et at 108mph, that was with very slow 2.5s 60ft due to traction
with street tyres and axle tramping.

Also I have
BA XR6 Turbo upper plenum/Manifold $30
BA XT lower plenum/Manifold $20
BA XT injectors (I have been told are same as Turbo injectors) $50
BA XT Fuel Rail and regulator $20

I'll quite gladly take these parts off your hands and pay for postage, assuming you'll post to WA that is...

-Heat shields (price?)
-Oil feed line (price?)
-BA lower intake runners ($20)
-Fuel rail ($20)

The lower manifold and injector rail is ok for me to sell right away.

Give me a PM with offer on the heat sheilds and oil feed line and
once I get my replies I have been waiting on for my turbo setup & all is
a go ahead I will be able to sell off the pieces I wont be using to the best offer.


Basically these parts are all undecided for sale at present
until I know what new setup I will be finalising on just incase
the new setup falls through as will need to refit them.

Turbo- Offer
Actuator (15psi)- Offer
Turbo exhaust manifold- Offer
Heat sheilds- Offer
Turbo oil line- Offer
X-Force Dump Pipe- Offer
Plazmaman pipe & Hose (Turbo to custom airbox)- Offer



All other parts are fine for me to sell straight away

Crossover $50
Factory Pipes and Hoses $30
XR6 Turbo Factory Cooler with mounting brackets $120
XR6 Turbo Upper Plenum/Manifold/Runners $30
XT Lower Plenum/Manifold/Runners $20
XT Injectors $50
XT Fuel Rail & Regulator $20


Fordman351 if you want to purchase the lower manifold and Fuel Rail,
straight away. PM me your address details so I can get postage costs for you.


Cheers
Paul

i'm interested on the turbo, and maybe injector rail,reg ,hoses ,pipes if they look like there going to fit 96,model xr6 ,would it be ok for me to inspect the turbo, i live in Marsden 10 minutes away

PM sent regarding fuel rail, lower runners and heat shields.

PM's sent shortly to all

Not much left now.

Sold

Heat Sheilds
Lower Runners
Injector Rail
Turbo
Oil & Coolant lines
Exhaust Manifold


Pending

X-Force Dump
X Over Pipes and Hoses
XR Intercooler


Thanks to all from here that have purchased.

Please lock, or remove.

SOLD

Not Available for sale anymore