|
| dumpdef |
|
||
|
hey fritzz thanx for that im going to have a chat with the bloke doin my install 2day so ill run threw those box mods with him, also i went on the nizpro website couldnt find nething for the ef's, ideally id like one from ebs_4l but if not ill get a nizpro item is there much fukin around to fit them, oh and with the cam could i just get say an rspec 6 cam kit (valve springs and venier gear) from the rpd boys or would i need a custom grind to suit turbo etc thanx again man
_________________ Piss On Holden!!!!
|
||
| Top | |
||
| fritzz |
|
|||
|
nizpro dont make the plenums for ef flaons, thay only make stuff for ba's but the ba plenum fits on the el/ef bottom half of bbm manifold. they are fairly easy to install when u buy the plenum it will come with all the s**t u need to install.
yeh i would go for the ebs_4l plenum, nizpro was the only 1's around when i wanted 1. nizpro will probaly cost 2x more than a ebs_4l 1 and work just as well if not better.. i wouldent have a clue about that cam so i dont know, but usally the big n/a cam seem to work well with turbo setup. like stevo he got 410rwhp on 7psi with a dev5 head and cam on a 214,000km old engine.
_________________ # 1997 EL Falcon GLI - 600+rwkw |
|||
| Top | |
|||
| dumpdef |
|
||
|
awsome ill get an r spec 6 cam package then and ill hopefully b able to get a plenum off ebs_4l thanx for all ya help man its been great realy appreciated u no ur s**t
_________________ Piss On Holden!!!!
|
||
| Top | |
||
| ebs_4l |
|
||
|
looks like i need to pull my finger out my a*** and get fabricating...
_________________ EB 4L, 8.4:1, R154, GT4202r, 4in exhaust, Greenslade Engineering exhaust manifold, plenum chamber, 90mm throttle, Garrett W2A cooler, Surecam custom, autronic SM4, Bosch 120lb, Crane HI-6, LX-92, LM-1, Turbosmart Reg, 2x bosch 044, turbosmart 48 gate. 470kw+ @ 18PSI |
||
| Top | |
||
| dumpdef |
|
||
|
hahaha s**t yeh get crackin:D u can put me down for a plenum strait up,
 :D
_________________ Piss On Holden!!!!
|
||
| Top | |
||
| Sandstone_EB_Fairmont |
|
|||
|
Hey Id like to turbocharge my stock EB Fairmont engine. But one of my mates says that the engine wont handle it. I read in a HOT4s mag that the crank-shaft can handle twice the stock power.
Is it possible to just buy a turbo and bolt it on? some pics of turbo EBs would be great. (I think a few of the pics above are an EB but im not sure)
_________________ -1994 EF XR6 + Factory 5speed = Fun |
|||
| Top | |
|||
| Gaz |
|
||
|
not even close.
need turbo manifold oil lines new computer injectors and fuel pump. dont really expect to get it done for under 5k and thats doing it extremly cheap. have a read of chefs sticky at the top of thsi forum
_________________ 2007 Steel BF Ghia MKII V8 - 19" GTP's + Superlows |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 11 guests |
