Fordmods Logo

time for a revamp EB6T 

 

Page 10 of 11 [ 156 posts ] Go to page Previous  1 ... 7, 8, 9, 10, 11  Next

 
 Post subject: Re: time for a revamp EB6T
Posted: Tue Jan 19, 2010 10:29 pm 
Getting Side Ways
Offline

Age: 39

Posts: 868

Joined: 23rd Sep 2005

Ride: eb falcon

Location: kadina
SA, Australia

The plan with the wastegate is, to have the current external gate, and also another gate plumbed into the cooler piping. Both working with the same spring pressure, and both controlled off the same boost solenoid. When the boost setpoint is reached, both gates should start to open together, currently, my manifold gate wont control boost.. It just keeps on pumping (exactly the same thing happened with my gt35 setup, went through many different configs, and eventually had to vent the exhaust from the turbine housing, to allow it to vent enough for proper boost control)

I didnt expect the new turbo to have the same issue, as the turbine flows considerably more. But I did, so the fix was to rip the spring out the v-port, and set it up til it was just leaking enough air that the wastegate was able to control the boost ok. So, with the wastegate right open, it will hold say 15PSI, and then that puts the other couple of psi of control onto the wastegate.

The new setup will be a massive improvement, because I will be able to enjoy 100% spoolup, at minimum rpm, but also have my boost controlled properly... As it is right now, the spoolup is s**t.. As it needs to overcome the massive air leak created by my bypassing BOV.

But anyway, it willl be sweet with my planned changes. The turbo will be turning no more faster than it is right now.

Dont have any recent pics..

The term "stock bottom end" is used fairly loosely, as I have spent considerable money on the bottom end in the past.. Stock refers to the parts in the rotating assembly, while the pistons are not stock, neither is the condition of the rotating parts. The crank has been blueprint ground and index checked, oil galleries chamfered, crack tested, balanced. Harmonic balancer and flywheel assy balanced to crank. The rods were closed and honed, crack tested, and balanced across all the small and big ends (it has original 1992 rod bolts). The block has been crack tested and all main caps line bored (original main cap bolts) It runs acl race series bearings, race series pistons and rings, crow cams timing chain and adj gear.

When i get it going again ill have it up Kadina. Tonight I just finished a bosch 160A alternator conversion on it, with all the pumps, fans and other s**t on it, even my 120A rewind couldnt keep up once the lights were on at night.

Whats the latest with your bus Ben?? How much power you making? did you ever build that motor using the Howards rods??

Brad

 

_________________

EB 4L, 8.4:1, R154, GT4202r, 4in exhaust, Greenslade Engineering exhaust manifold, plenum chamber, 90mm throttle, Garrett W2A cooler, Surecam custom, autronic SM4, Bosch 120lb, Crane HI-6, LX-92, LM-1, Turbosmart Reg, 2x bosch 044, turbosmart 48 gate. 470kw+ @ 18PSI

Top
 Profile  
 
 
 Post subject: Re: time for a revamp EB6T
Posted: Tue Jan 19, 2010 11:42 pm 
Getting Side Ways
Offline
User avatar

Age: 35

Posts: 975

Joined: 26th Nov 2004

Ride: el falcon

Power: 608 rwkw

Location: Waroona
WA, Australia

ebs_4l wrote:
Whats the latest with your bus Ben?? How much power you making? did you ever build that motor using the Howards rods??

Brad


managed 468rwkw @ 18psi on bp98 with the old setup, that was pretty much on its limit but

the new bottom end is all built with the head of the old engine and a new custom surecam..

it just got dropped it in the car last week... now im onto wiring up a autronic 500r and 6 coils and plumbing a surge tank and 044 pumps... then i gotta build a decent exhaust

 

_________________

# 1997 EL Falcon GLI - 600+rwkw

# 2008 FPV FG GTE - Xa Coilovers, 20x8/ 20x10 Fairladys

Top
 Profile  
 
 
 Post subject: Re: time for a revamp EB6T
Posted: Wed Jan 20, 2010 12:06 am 
Getting Side Ways
Offline

Age: 39

Posts: 868

Joined: 23rd Sep 2005

Ride: eb falcon

Location: kadina
SA, Australia

500r and 6 coil.... Now were talking. Any particular reason for that?? did you have any missfiring??

 

_________________

EB 4L, 8.4:1, R154, GT4202r, 4in exhaust, Greenslade Engineering exhaust manifold, plenum chamber, 90mm throttle, Garrett W2A cooler, Surecam custom, autronic SM4, Bosch 120lb, Crane HI-6, LX-92, LM-1, Turbosmart Reg, 2x bosch 044, turbosmart 48 gate. 470kw+ @ 18PSI

Top
 Profile  
 
 
 Post subject: Re: time for a revamp EB6T
Posted: Wed Jan 20, 2010 7:39 pm 
Getting Side Ways
Offline
User avatar

Age: 57

Posts: 918

Joined: 6th Aug 2007

Gallery: 4 images

Ride: BA XR8

Location: Kellyville
NSW, Australia

Good to see ur still at it. Sorry to hear about the troubles though. What sort and size is ur 'gate???

Hope you get it sorted...

Cheers

Daz

 

_________________

BA XR8 Boss 260
DAZFAB......Now Mobile
Mink = GAY
DAZFAB MEMBERS ,,,,DA22LE, XTT909, TERRORISTGHIA, TROYMAN, SWC, FAT245

Top
 Profile  
 
 
 Post subject: Re: time for a revamp EB6T
Posted: Wed Jan 20, 2010 10:08 pm 
Getting Side Ways
Offline
User avatar

Age: 35

Posts: 975

Joined: 26th Nov 2004

Ride: el falcon

Power: 608 rwkw

Location: Waroona
WA, Australia

ebs_4l wrote:
500r and 6 coil.... Now were talking. Any particular reason for that?? did you have any missfiring??


haha yeh i managed to get the 500r at a decent price...

yeh on the 468rwkw tune i had to gap the plugs down to .7mm to stop spark blowout... but realy i just want an ignition system that is more than good enough so i dont have to worry about it..

 

_________________

# 1997 EL Falcon GLI - 600+rwkw

# 2008 FPV FG GTE - Xa Coilovers, 20x8/ 20x10 Fairladys

Top
 Profile  
 
 
 Post subject: Re: time for a revamp EB6T
Posted: Wed Jan 20, 2010 10:43 pm 
Getting Side Ways
Offline

Age: 39

Posts: 868

Joined: 23rd Sep 2005

Ride: eb falcon

Location: kadina
SA, Australia

What ign were you using then? did you have a CDI?

Im using a HI-6, and so far havent experienced spark problems... However, a 6 coil system would be sweet

 

_________________

EB 4L, 8.4:1, R154, GT4202r, 4in exhaust, Greenslade Engineering exhaust manifold, plenum chamber, 90mm throttle, Garrett W2A cooler, Surecam custom, autronic SM4, Bosch 120lb, Crane HI-6, LX-92, LM-1, Turbosmart Reg, 2x bosch 044, turbosmart 48 gate. 470kw+ @ 18PSI

Top
 Profile  
 
 
 Post subject: Re: time for a revamp EB6T
Posted: Wed Jan 20, 2010 10:55 pm 
Getting Side Ways
Offline
User avatar

Age: 35

Posts: 975

Joined: 26th Nov 2004

Ride: el falcon

Power: 608 rwkw

Location: Waroona
WA, Australia

ebs_4l wrote:
What ign were you using then? did you have a CDI?

Im using a HI-6, and so far havent experienced spark problems... However, a 6 coil system would be sweet


yeh i was running the crane hi6 with lx92 coil as well

 

_________________

# 1997 EL Falcon GLI - 600+rwkw

# 2008 FPV FG GTE - Xa Coilovers, 20x8/ 20x10 Fairladys

Top
 Profile  
 
 
 Post subject: Re: time for a revamp EB6T
Posted: Wed Jan 20, 2010 11:00 pm 
Getting Side Ways
Offline

Age: 39

Posts: 868

Joined: 23rd Sep 2005

Ride: eb falcon

Location: kadina
SA, Australia

and std dizzy??

thats strange. had you ever re-indexed the rotor to set the point of full boost timing to be right in the middle of the rotor button and lead contact? or left std rotor angle

 

_________________

EB 4L, 8.4:1, R154, GT4202r, 4in exhaust, Greenslade Engineering exhaust manifold, plenum chamber, 90mm throttle, Garrett W2A cooler, Surecam custom, autronic SM4, Bosch 120lb, Crane HI-6, LX-92, LM-1, Turbosmart Reg, 2x bosch 044, turbosmart 48 gate. 470kw+ @ 18PSI

Top
 Profile  
 
 
 Post subject: Re: time for a revamp EB6T
Posted: Wed Jan 20, 2010 11:31 pm 
Getting Side Ways
Offline
User avatar

Age: 35

Posts: 975

Joined: 26th Nov 2004

Ride: el falcon

Power: 608 rwkw

Location: Waroona
WA, Australia

yep standard dizzy...

definitely indexed the rotor which did help a bit...

 

_________________

# 1997 EL Falcon GLI - 600+rwkw

# 2008 FPV FG GTE - Xa Coilovers, 20x8/ 20x10 Fairladys

Top
 Profile  
 
 
 Post subject: Re: time for a revamp EB6T
Posted: Wed Jan 20, 2010 11:49 pm 
Getting Side Ways
Offline

Age: 39

Posts: 868

Joined: 23rd Sep 2005

Ride: eb falcon

Location: kadina
SA, Australia

yea ok, be interesting to see if I run into problems with spark. I would have thought that with E85 I would have seen issues if I was going to, it requires higher spark energy due to the denser mixture..

Either way, I HOPE I dont, because I cant afford ign upgrades.

Do you have the dizzy in place to act as a sync sensor still then?

 

_________________

EB 4L, 8.4:1, R154, GT4202r, 4in exhaust, Greenslade Engineering exhaust manifold, plenum chamber, 90mm throttle, Garrett W2A cooler, Surecam custom, autronic SM4, Bosch 120lb, Crane HI-6, LX-92, LM-1, Turbosmart Reg, 2x bosch 044, turbosmart 48 gate. 470kw+ @ 18PSI

Top
 Profile  
 
 
 Post subject: Re: time for a revamp EB6T
Posted: Wed Jan 20, 2010 11:56 pm 
Getting Side Ways
Offline

Age: 39

Posts: 868

Joined: 23rd Sep 2005

Ride: eb falcon

Location: kadina
SA, Australia

forget that sync question, i just saw the pics in your thread, and I can see the au spec cam pos sensor

Oh, and I must say, congrats on the black comp cover, rocker cover and plenum... reminds me of mine

 

_________________

EB 4L, 8.4:1, R154, GT4202r, 4in exhaust, Greenslade Engineering exhaust manifold, plenum chamber, 90mm throttle, Garrett W2A cooler, Surecam custom, autronic SM4, Bosch 120lb, Crane HI-6, LX-92, LM-1, Turbosmart Reg, 2x bosch 044, turbosmart 48 gate. 470kw+ @ 18PSI

Top
 Profile  
 
 
 Post subject: Re: time for a revamp EB6T
Posted: Thu Jan 21, 2010 12:07 am 
Getting Side Ways
Offline
User avatar

Age: 35

Posts: 975

Joined: 26th Nov 2004

Ride: el falcon

Power: 608 rwkw

Location: Waroona
WA, Australia

au cam and crank triggers for sure

yeh wanted it a bit more stealth black looks good, had planned on something a little different but didn't have the time

 

_________________

# 1997 EL Falcon GLI - 600+rwkw

# 2008 FPV FG GTE - Xa Coilovers, 20x8/ 20x10 Fairladys

Top
 Profile  
 
 
 Post subject: Re: time for a revamp EB6T
Posted: Tue Mar 16, 2010 7:33 am 
Parts Gopher
Offline

Posts: 76

Joined: 3rd Mar 2007

Location: lismore
NSW, Australia

sorry to dig this up ebs, but how has the car been going.
Top
 Profile  
 
 
 Post subject: Re: time for a revamp EB6T
Posted: Mon Apr 04, 2011 10:10 am 
Getting Side Ways
Offline
User avatar

Age: 47

Posts: 5361

Joined: 31st Oct 2005

Gallery: 28 images

Ride: NC II Fairlane

Location: morayfield
NSW, Australia

almost 12 month bump.. soo much potential in this thing. im hoping we get an update

 

_________________

Prendre soin de sa sante www.viagrasansordonnancefr.com vente libre en France

Top
 Profile  
 
 
 Post subject: Re: time for a revamp EB6T
Posted: Mon Apr 04, 2011 10:25 am 
Parts Gopher
Offline
User avatar

Age: 14

Posts: 59

Joined: 9th Aug 2009

Gallery: 22 images

Ride: A massive sideways utensill...

Location: Wagga Wagga
NSW, Australia

i am rather eager to hear some more about this wepon also..

Where are you EB6T?? :(

 

_________________

XR6, 3''CAI, sick'o BBM, no AC, 2.5''exhaust, special cat, PWR radiator&expansion-tank, BTR, kevlar bands, JMM converter, shiftkit, 4 pin 3.91:1, 31spline billets, minispool, Nolathane, RDA golds, My interior, genuine GT's.. (gallery) SpeedFlow

Top
 Profile  
 
Display posts from previous:
Sort by  
 Page 10 of 11  [ 156 posts ]  Go to page Previous  1 ... 7, 8, 9, 10, 11  Next

Who is online

Users browsing this forum: Google [Bot] and 17 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

 

 

It is currently Fri Mar 29, 2024 5:24 pm All times are UTC + 11 hours

 

 

(c)2014 Total Web Solutions Australia - Australian Web Hosting and Domain Names