|
| RuchEa |
|
||
|
AU TE50 200kw motor, 90,000kms?
Thanks
_________________ EB XR6 project almost complete!
|
||
| Top | |
||
| Molloy |
|
|||
|
just the motor itself?
_________________ SS Inductions CAI, K&N Filters, M-spec FMC, Turbosmart BOV, 8psi capa tune, X-force cat. |
|||
| Top | |
|||
| RuchEa |
|
||
|
yup
_________________ EB XR6 project almost complete!
|
||
| Top | |
||
| Molloy |
|
|||
|
id say 1000-3000
_________________ SS Inductions CAI, K&N Filters, M-spec FMC, Turbosmart BOV, 8psi capa tune, X-force cat. |
|||
| Top | |
|||
| RuchEa |
|
||
|
Thats alrite, was thinkin closer too 800-1000
Nothing remotely similar available on ebay! Anyone else think differently?
_________________ EB XR6 project almost complete!
|
||
| Top | |
||
| EL XR8 |
|
|||
|
I'm gathering this is the motor out of the car EBTS50 is selling.
If its the 200kw T series motor, it'll be worth a bit more than a grand. The heads and manifold alone would be worth over 1k. Let alone a motor that goes with them. I'd say around 2k at least. If not more. |
|||
| Top | |
|||
| V8 Ghia Mike |
|
||
|
I saw a 200kW AU motor (red engine cover?) at a local wreckers for $3000 recently, complete.
That's still good value, considering the cost of building one. Mike
_________________ EF Ghia 5.0 - XR8 in a tuxedo....classy, low and loud |
||
| Top | |
||
| [HMASEL] |
|
|||
|
Fit an EL?
I might be interested  :D
|
|||
| Top | |
|||
| Vic |
|
|||
|
RuchEa wrote: AU TE50 200kw motor, 90,000kms?
Thanks I'd put a figure of $2,000 to $2,500 on it if its 90,000kms.
_________________ 5.6L of carbon footprint. |
|||
| Top | |
|||
| jagga |
|
||
|
i picked up a 220 motor for my ef.for 4k but that came with a trans computer loom all accesories. tail shaft headers. etc...
does this motor come with accesories or is it just a block,heads etc. keep in ming. if it has the EDIS setup still there is quite a bit or buggering around to either loom match it or change the front end accesories. i had to change balencer. coil packs to distributor, headers, comp and loom. throttlebody(my choice) and a few other bits and pieces. oh asnd the little loom thingi from the trans to the loom near the window washer bottle. b sure u have a budget set. and u know what u need if this is the case coz i didnt and i have had a heap of dramas. lol altho its been good to learn the stuff i have involved with it... jagga
_________________ Ef xr8. Charged 9psi, tw 170 heads,track heat intakes,1.72 rockers, f303 cam, custom plazma man/ rapid cooler, 60lb injectors, tko600, sct eliminator, aeromotive fuel system. |
||
| Top | |
||
| EL XR8 |
|
|||
|
The guy is after high 2k mark, for a whole car, not just the motor.
Some of the guys are obviously working out if the motor is worth buying the whole car for. |
|||
| Top | |
|||
| RuchEa |
|
||
|
[HMASEL] wrote: Fit an EL?
I might be interested :DCurrently in an EB so yeh except maybe K frame! Not sure though!
_________________ EB XR6 project almost complete!
|
||
| Top | |
||
| RuchEa |
|
||
|
EL XR8 wrote: I'm gathering this is the motor out of the car EBTS50 is selling.
If its the 200kw T series motor, it'll be worth a bit more than a grand. The heads and manifold alone would be worth over 1k. Let alone a motor that goes with them. I'd say around 2k at least. If not more. Yeh looking at buyin it! should scrape on by with cash if i buy it! just havent got anywere to put it till i sell it! So yeh just researching sellability!
_________________ EB XR6 project almost complete!
|
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 15 guests |
