 |
|
|
|
|
|
|
|
|
|
nare
Fordmods Oompa Loompa
Posts: 25
Joined: 21 Dec 2004
Location: melb VIC, Australia
View User Gallery (0)
|
 Posted: Wed Dec 29, 2004 7:00 pm Post subject: XR6T engine into AU? |
 |
|
Would it be possible? What would be needed (other than the engine, duh!)?
Also would a stock auto hold up? |
|
| Back to top |
|
|
|
|
|
|
|
|
|
Disco Frank
Fordmods Junkie
Age:29
Posts: 13749
Joined: 05 Nov 2004
Location: Perth WA, Australia
View User Gallery (7)
|
| Posted: Wed Dec 29, 2004 9:10 pm Post subject: |
|
|
hey dude welcome to fordmods!
this has been convered b4, yes it will fit but u will need a lot of work for it to run ie full aftermarket ecu ie motoec is about the the only thing u will find can run the engine thats about 6k then there is the engine itself not sure on cost but over 6k again i would assume also the stock auto would need beefing up!
be cheaper and easier to turbo the car u have now |
|
| Back to top |
|
|
|
|
|
|
|
|
|
He[X]eN
Fordmods Stock as a Rock
Posts: 107
Joined: 07 Nov 2004
Location: Melbourne VIC, Australia
View User Gallery (0)
|
| Posted: Wed Dec 29, 2004 10:54 pm Post subject: |
|
|
| Disco Frank wrote: | hey dude welcome to fordmods!
this has been convered b4, yes it will fit but u will need a lot of work for it to run ie full aftermarket ecu ie motoec is about the the only thing u will find can run the engine thats about 6k then there is the engine itself not sure on cost but over 6k again i would assume also the stock auto would need beefing up!
be cheaper and easier to turbo the car u have now |
Was quoted from a Ford service centre 16k for the engine!  |
|
| Back to top |
|
|
|
|
|
|
|
|
|
chunkz
Fordmods - Getting Side Ways
Age:21
Posts: 5314
Joined: 06 Nov 2004
Location: Melbourne, S.E Suburbs VIC, Australia
View User Gallery (4)
|
| Posted: Wed Dec 29, 2004 10:57 pm Post subject: |
|
|
| if your gunna spend that much, may aswell go all out and try for a 6 speed conversion |
|
| Back to top |
|
|
|
|
|
|
|
|
|
Bomber
Fordmods - Getting Side Ways
Age:25
Posts: 626
Joined: 06 Nov 2004
Location: Rosebud VIC, Australia
View User Gallery (2)
|
| Posted: Wed Dec 29, 2004 11:08 pm Post subject: |
|
|
| need new bonnet or bonnet bulge might not fit near firewall, i looked at this option and gave up pretty quick its just not worth the $$$ |
|
| Back to top |
|
|
|
|
|
|
|
|
|
xr8 dismantler
Age:37
Posts: 3143
Joined: 06 Nov 2004
Location: MELBOURNE VIC, Australia
View User Gallery (0)
|
| Posted: Wed Dec 29, 2004 11:13 pm Post subject: |
|
|
i can supply the motor & auto with all the looms and P.C.M
for $7500 |
|
| Back to top |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
