 |
|
|
|
|
|
|
|
|
|
|
|
aphexer
Fordmods - Getting Side Ways
Age:24
Posts: 657
Joined: 08 Nov 2004
Location: Eastern Suburbs VIC, Australia
View User Gallery (1)
|
 Posted: Wed Jan 12, 2005 11:50 am Post subject: |
 |
|
i got pacemaker headers PH4499 and a full 2.5" redback exhaust (cat, muffler, pipes) fitted for $900 to my EF xr6.
definately feels like it has more poke.
$1400 is a joke for lower-end gear! |
|
| Back to top |
|
|
|
|
|
|
|
|
|
Casper
Fordmods - Smokin em up
Age:38
Posts: 256
Joined: 13 Nov 2004
Location: Melbourne VIC, Australia
View User Gallery (0)
|
| Posted: Wed Jan 12, 2005 2:24 pm Post subject: |
|
|
| stiddy wrote: | haha casper a XR6 series 1 manual with the similar mods shouldnt be too far off your pace or too far infront 
I think im gonna end up going for a ser of JMM race series.. and a 2.5in lukey system.. its garenteed to work and i havent ever herd 1 bad thing about them.. just building up the bank first..
is it worth getting the hpc.. will it make MUCH difference? cause i think i'll just go the race series without..
i know you need a good exhaust system on the car.. but i cant justify spending near 900 bucks just for a set of exractors.. but i can on a full system.. unless the hpc will give me alot more gains then non.. |
I didnt bother with HPC. Looks good but performance is marginal if at all better.
The manual will give you a big advantage. Grab the JMM's, a chiptorque chip and the 2.5" exhaust and your in 14.7-14.8 territory. The manual makes that much difference.
Just be prepared to kill a clutch at the drags. |
|
| Back to top |
|
|
|
|
|
|
|
|
|
hornet
Fordmods - Getting Side Ways
Posts: 916
Joined: 27 Nov 2004
Location: Berri SA, Australia
View User Gallery (4)
|
| Posted: Wed Jan 12, 2005 6:37 pm Post subject: |
|
|
| Casper, Do you think I'd be able to achieve those ET's with my car with a decent set of extractors? (specs in signature) |
|
| Back to top |
|
|
|
|
|
|
|
|
|
Casper
Fordmods - Smokin em up
Age:38
Posts: 256
Joined: 13 Nov 2004
Location: Melbourne VIC, Australia
View User Gallery (0)
|
| Posted: Wed Jan 12, 2005 7:06 pm Post subject: |
|
|
| hornet wrote: | | Casper, Do you think I'd be able to achieve those ET's with my car with a decent set of extractors? (specs in signature) |
Simple answer, I dont know.
Looking at your 1/8th time your ET is very similar to mine (9.751) but your MPH is much slower (74.21mph) so you have not got the same momentum at that point. At a guess your running about a 15.7 or 15.8 now. Hard to tell. I do know that your stock header (if thats whats on there) would be killing your high revs so I would say putting on a decent set of headers that work with your engine would make a noticable improvement.
I would guess that you would get similar times certainly, but I wont guess what. Anywhere from 15.2 to 14.8 would be feasable, I kust dont know. |
|
| Back to top |
|
|
|
|
|
|
|
|
|
hornet
Fordmods - Getting Side Ways
Posts: 916
Joined: 27 Nov 2004
Location: Berri SA, Australia
View User Gallery (4)
|
| Posted: Thu Jan 13, 2005 7:34 pm Post subject: |
|
|
I'm not too sure that mph is correct, I have run 10.2 @70mph before. And in most of my eliminations of was on the anchors across the line so I didn't break out.. not good for acurate mph's  |
|
| Back to top |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
| |
| (c)2002-2009 Matti Jones and Brad Evans |
[32 queries :: 0.03687 seconds ]
|
|
