 |
|
|
|
|
|
|
|
|
|
|
FastFutura
Fordmods Stock as a Rock
Age:24
Posts: 112
Joined: 05 Nov 2004
Location: Perth WA, Australia
View User Gallery (8)
|
 Posted: Tue Jan 11, 2005 10:53 am Post subject: How to Reset computer controlled idle? |
 |
|
after fitting my new cam and resetting the computer in the car, setting the base idle so it dont stall cos its lumpy, (set at 900 RPM)
it holds the revs up at around 2000 -2500 for ages then slowly drops down to the base idle of 900 or 1100 depending on how stupid it is being.
its manual and it used to always rev up and drop straight back down to the base idle.
(i have manny computer) (heh unless carl swapped it with his auto puter without me knowing)
how do i either kill that motor controlled idle or get it to drop to base idle faster..
at the moment i got no engine braking.. more like a fkn cruise control at 2000- 2500 revs. :S
thanks |
|
| Back to top |
|
|
|
|
|
|
|
|
|
hornet
Fordmods - Getting Side Ways
Posts: 916
Joined: 27 Nov 2004
Location: Berri SA, Australia
View User Gallery (4)
|
| Posted: Tue Jan 11, 2005 8:44 pm Post subject: |
|
|
I got sick of the computer controlled idle in my EL manual, so I disconnected the Idle Speed Controller valve. Now my car returns to base idle when i close the throttle on gear shifts.
That might fix the problem your talking about, it makes the car behave 'normal'. I'm not sure if the ED's have this valve, but it may be something to consider. |
|
| Back to top |
|
|
|
|
|
|
|
|
|
Fakertaker
Fordmods Stock as a Rock
Age:24
Posts: 109
Joined: 14 Nov 2004
Location: Sydney, The Shire NSW, Australia
View User Gallery (0)
|
| Posted: Wed Jan 12, 2005 6:57 pm Post subject: |
|
|
The EDs have the same valve, but what you might find is that it will idle too low with the cam and without the ISC valve raising the idle. Mine didn't work on my ED and the idle was nearly too low for the standard futura cam. But give it a shot I guess, If the idle isn't too low for the cam then you will be sweet.
I had problems with my AU with the idle not being raised enough, and sometimes if i changed gears while braking and turning the car would stall....
good luck,
matt |
|
| Back to top |
|
|
|
|
|
|
|
|
|
FastFutura
Fordmods Stock as a Rock
Age:24
Posts: 112
Joined: 05 Nov 2004
Location: Perth WA, Australia
View User Gallery (8)
|
| Posted: Thu Jan 13, 2005 3:02 pm Post subject: |
|
|
fixed!!!
technique =
warm running temp
disconnect TCP wires to throttle body controller.
turn car on .. idle
adjust idle screw to lowest idle possible, if its easy then its too high. if it stalls... too low. somewhere in between.
discharge positive terminal onto negative terminal of battery.. (theres no sparks,. this is to reset the puter by draining all the capacitors n s**t i spose.)
leave for about 10 -15 min.
reconnect..
drive away.. (will take about 600 ks to get fully normal (ie puters used to new cam etc)
thanks SVOXR6 for this method |
|
| Back to top |
|
|
|
|
|
|
|
|
|
SVO XR6
Fordmods - Getting Side Ways
Age:24
Posts: 1680
Joined: 05 Nov 2004
Location: Scaaabz WA, Australia
View User Gallery (1)
|
| Posted: Thu Jan 13, 2005 4:11 pm Post subject: |
|
|
No worries mate, hope all goes well  |
|
| Back to top |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
| |
| (c)2002-2009 Matti Jones and Brad Evans |
[32 queries :: 0.04261 seconds ]
|
|
