 |
|
|
|
|
|
|
|
|
|
phongus
Fordmods Junkie
Age:23
Posts: 8839
Joined: 17 May 2005
Location: Melbourne VIC, Australia
View User Gallery (11)
|
 Posted: Wed Nov 29, 2006 10:34 pm Post subject: Electric motors |
 |
|
Now since this new section just popped up I just had to whore a post on here. Anyways H3AT, one of my other mates and I were planning on slapping together a dodgy electric car. We have half a shell (my battered EA) and we have the motors (I think 2 x 9" not too sure).
All I need is the power control thingy ma bob (don't know what it is called) that is needed to keep the juice flowing evenly and won't blow anything up and also of course the power source.
Though I am not really a total noob with electric motors and electricity in general, I need more info on what is needed to get one of these running and also what precautions and specs of motors, batteries and off the shelve equipment. Keeping in mind this is a low cost project...if it fails I say OH WELL.
And yes I have had thought about getting a smaller car shell though I can't find one just lying around while I have the EA for free.
I have read the one about the 2 x 9" motors in the 180XS or whatever it was pulling good figures on the dyno... though it was a lighter car and had more money spent on it. I don't want this project between us 3 to cost us an arm and a leg. Most little things such as wiring and stuff can be found in my garage or H3AT's house. So not much money going to be spent on screws wiring, switches, brackets and such.
Anyways any help would be nice =D
phong =P~ |
|
| Back to top |
|
|
|
|
|
|
|
|
|
EFFalcon
Fordmods - Getting Side Ways
Age:25
Posts: 3064
Joined: 05 Nov 2004
Location: Mornington Peninsula VIC, Australia
View User Gallery (11)
|
| Posted: Wed Nov 29, 2006 10:38 pm Post subject: |
|
|
| i think no matter how you go about it it'll be an expensive project. |
|
| Back to top |
|
|
|
|
|
|
|
|
|
phongus
Fordmods Junkie
Age:23
Posts: 8839
Joined: 17 May 2005
Location: Melbourne VIC, Australia
View User Gallery (11)
|
| Posted: Wed Nov 29, 2006 10:42 pm Post subject: |
|
|
| EFFalcon wrote: | | i think no matter how you go about it it'll be an expensive project. |
OH SNAP!!!....batteries will be the most expensive thing =(
Remember...so long as it moves forward at a reasonable speed we'll be happy. |
|
| Back to top |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
phongus
Fordmods Junkie
Age:23
Posts: 8839
Joined: 17 May 2005
Location: Melbourne VIC, Australia
View User Gallery (11)
|
| Posted: Wed Nov 29, 2006 11:07 pm Post subject: |
|
|
The batteries don't have to be new. Then again I don't even know how many I need. Marine batteries are going for like 200 or something. Given that each battery produces 12V and I need 240V I'm going to need 20 batteries...plus maybe 5 more for the sake of it. That comes to over $4000.
If anyone has spare batteries that may still work after some charging...that would be awesome... I already have one HAHAHA...thats at least another 19 to go.
phong =P~ |
|
| Back to top |
|
|
|
|
|
|
|
|
|
Disco Frank
Fordmods Junkie
Age:29
Posts: 13576
Joined: 05 Nov 2004
Location: Perth WA, Australia
View User Gallery (7)
|
| Posted: Wed Nov 29, 2006 11:08 pm Post subject: |
|
|
ahh a few lead accid car batteries will be fine 
might weigh a bit...
or u could get a few hundred nimh AA's and make a few packs, there is a car in europe with this setup and runs for about 2hrs irrc but has regenative braking |
|
| Back to top |
|
|
|
|
|
|
|
|
|
phongus
Fordmods Junkie
Age:23
Posts: 8839
Joined: 17 May 2005
Location: Melbourne VIC, Australia
View User Gallery (11)
|
| Posted: Wed Nov 29, 2006 11:24 pm Post subject: |
|
|
| Disco Frank wrote: | ahh a few lead accid car batteries will be fine
might weigh a bit...
or u could get a few hundred nimh AA's and make a few packs, there is a car in europe with this setup and runs for about 2hrs irrc but has regenative braking |
 that would require a lot of nimh AA's to produce enough current for the motors. Though this is just a fun thing...if we spend a lot we won't even bother really. Anything that can be done for cheap will be done...but batteries has always been the main problem for electric cars...too expensive and too much money. I reckon I should just get a whole lot of lemons and copper coins and make my own batteries HAHAHA
phong =P~ |
|
| Back to top |
|
|
|
|
|
|
|
|
|
WIKWOK
Fordmods Parts Gopher
Age:23
Posts: 59
Joined: 26 Jun 2006
Location: Albury/Wodonga VIC, Australia
View User Gallery (9)
|
| Posted: Thu Nov 30, 2006 11:01 pm Post subject: |
|
|
Hey mate,
I have been doing quite a bit of research on these electric cars.. particularly the Hydrogen Fuel Cell powered beasts..
So i hope i might be of some assistance..
Just a few quick things to bring up..
* What voltage and wattage are your motors?
* Do you have any torque, rpm, etc type specs on them?
* What kind of drive were you planning on?
* How do you plan on charging the batteries?
Seeing as this car is just an experiment i would imagine you aren't expecting much of a result..
I have a couple of contacts who have created electric cars for themselves.. One of them in a Old School Mini Cooper.. So i can squeeze their brains for info too..
I will keep an eye out on this thread for sure..
Cheers,
Nik |
|
| Back to top |
|
|
|
|
|
|
|
|
|
phongus
Fordmods Junkie
Age:23
Posts: 8839
Joined: 17 May 2005
Location: Melbourne VIC, Australia
View User Gallery (11)
|
| Posted: Fri Dec 01, 2006 1:37 pm Post subject: |
|
|
Cheers nik =D I haven't even seen the motors myself :S...but lets just hope they are not 3 phase motors at 340V cause that would cause more problems.
Yeah I know a fair bit about Hydrogen Fuel cars....the only problem is supply of Hydrogen (pretty damn expensive) and also the Hydrogen storage containers. Being a nanotechnologist I had to look into different methods of hydrogen cells and the best way was through new materials such as carbon-nanotubes which are light weight and can with hold a lot of pressure. So yeah it is interesting but requires a few more years of research.
phong =P~ |
|
| Back to top |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Walker
Technical Contributor
Age:37
Posts: 8581
Joined: 05 Nov 2004
Location: Melbourne VIC, Australia
View User Gallery (5)
|
| Posted: Mon Dec 04, 2006 8:03 pm Post subject: |
|
|
| Yeah Happy, he nano nuffin. |
|
| Back to top |
|
|
|
|
|
|
|
|
|
Mitch_
Cruise Moderator
Age:20
Posts: 5902
Joined: 05 Nov 2004
Location: Streets of Brisvegas QLD, Australia
View User Gallery (6)
|
| Posted: Mon Dec 04, 2006 8:07 pm Post subject: |
|
|
| phongus wrote: | | . Given that each battery produces 12V and I need 240V I'm going to need 20 batteries |
ummm dude! car batteries are DC, 240V is AC  Just a bit different! u can get an inverter u could get an electric generator
get 3 phase ran to your place an a huge extension cord mite turn our cheaper |
|
| Back to top |
|
|
|
|
|
|
|
|
|
Happy
Moderator
Age:35
Posts: 9965
Joined: 05 Nov 2004
Location: Perth WA, Australia
View User Gallery (4)
|
| Posted: Mon Dec 04, 2006 8:14 pm Post subject: |
|
|
| it's ok Mitch - he's a nanosomethingorother |
|
| Back to top |
|
|
|
|
|
|
|
|
|
Pulco
Fordmods - Getting Side Ways
Age:24
Posts: 1490
Joined: 01 Dec 2004
Location: Maitland NSW, Australia
View User Gallery (2)
|
| Posted: Mon Dec 04, 2006 8:15 pm Post subject: |
|
|
hey phong...i work on electric motors...
let me know wat u want to know and maybe u can help you!!
for instance....depending on voltage and frequency that determines wat speed ur wheels will spin....
ie...in australian stanards...the quickest a motor will turn is 3000 rpm cause of the voltage.and frequency....u can alter this by ising a varible frequency drive by up to whatever...but u have to make sure that the bearings adn the rotor are capable of these speeds..otherwise...u will destroy the internals of the motor...
also depending on wat power...and torque you are dependins the motor to out will depend on the acceleration and torque you get..
Last edited by Pulco on Mon Dec 04, 2006 8:25 pm, edited 2 times in total |
|
| Back to top |
|
|
|
|
|
|
|
|
|
The Dog
Fordmods - Getting Side Ways
Age:32
Posts: 2745
Joined: 24 May 2006
Location: Bordertown SA, Australia
View User Gallery (21)
|
| Posted: Mon Dec 04, 2006 8:18 pm Post subject: |
|
|
| Walker wrote: | | Yeah Happy, he nano nuffin. |
 |
|
| Back to top |
|
|
|
|
|
|
|
|
|
Walker
Technical Contributor
Age:37
Posts: 8581
Joined: 05 Nov 2004
Location: Melbourne VIC, Australia
View User Gallery (5)
|
| Posted: Mon Dec 04, 2006 8:36 pm Post subject: |
|
|
| We should call him Mork from Ork, Nano Nano!!! |
|
| Back to top |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Falcon96kickass
Cruise Moderator
Age:19
Posts: 1180
Joined: 09 Nov 2006
Location: Perth WA, Australia
View User Gallery (5)
|
| Posted: Wed Jan 03, 2007 10:08 pm Post subject: Electric Motors |
|
|
I would really worry about that stuff now aye to
Expensive Unless you have the money to do it
Electric motors arn't that good anyway
well not compaired to a Falcon Motor |
|
| Back to top |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
