 |
|
|
|
|
|
|
|
|
|
|
mitchg911
Age:22
Posts: 882
Joined: 06 Nov 2004
Location: Sydney NSW, Australia
View User Gallery (0)
|
 Posted: Fri Jan 28, 2005 4:46 pm Post subject: xf bumper rattle |
 |
|
is there a way to tighten the bolts holding on the rear bar of an xf? mine is losse (can be shaken by hand) and the sub rattles it like a bastard... i cant see how to get at the nuts to tighten it up, if there is any???
any ideas?
cheers
-mitch |
|
| Back to top |
|
|
|
|
|
|
|
|
|
smoke_
Cruise Moderator
Age:24
Posts: 5809
Joined: 05 Nov 2004
Location: Brisbane QLD, Australia
View User Gallery (7)
|
| Posted: Fri Jan 28, 2005 7:00 pm Post subject: |
|
|
im not sure if they're in the boot, i cant remember doing mine on my xf.
If not, they'll be underneath, shine a torch up there so you can see, and wiggle it around. |
|
| Back to top |
|
|
|
|
|
|
|
|
|
Interceptor
Fordmods - Getting Side Ways
Age:26
Posts: 7287
Joined: 05 Nov 2004
Location: Somewhere in QLD, Australia
View User Gallery (12)
|
| Posted: Fri Jan 28, 2005 9:30 pm Post subject: |
|
|
yea, they're in the boot, remove the plastic panel thats behind the taillights, the left ones are either side of the wedge shaped block that goes from the boot floor to the taillight panel and is about an inch wide, you gotta pull the spare out to get at the drivers side ones... while you're at it, pull the bumper off for 5 mins and put some silicone around where the beaver panel meets its mounts and where it bolts onto the body, mine rattles like a mofo, so i wouldnt be suprised if yours does too
(the beaver panel is the steel panel underneath the back bumper) |
|
| Back to top |
|
|
|
|
|
|
|
|
|
mitchg911
Age:22
Posts: 882
Joined: 06 Nov 2004
Location: Sydney NSW, Australia
View User Gallery (0)
|
| Posted: Sat Jan 29, 2005 4:59 pm Post subject: |
|
|
ok awesome,, i have pulled that plastic out looking,, must have assumed those bolts were for something else...
cheers for the replys.. *pulls out big shifter and charges over to car*
-mitch |
|
| Back to top |
|
|
|
|
|
|
|
|
|
Interceptor
Fordmods - Getting Side Ways
Age:26
Posts: 7287
Joined: 05 Nov 2004
Location: Somewhere in QLD, Australia
View User Gallery (12)
|
| Posted: Sat Jan 29, 2005 5:51 pm Post subject: |
|
|
| lol you wont get the drivers side ones with a shifter..... |
|
| Back to top |
|
|
|
|
|
|
|
|
|
mitchg911
Age:22
Posts: 882
Joined: 06 Nov 2004
Location: Sydney NSW, Australia
View User Gallery (0)
|
| Posted: Sat Jan 29, 2005 11:05 pm Post subject: |
|
|
| how about my trusty hammer and pry bar? hehe joking.. dont worry im sure i have something to do that up amoung dads rediculous assortment of tools |
|
| Back to top |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
| |
| (c)2002-2008 Matti Jones and Brad Evans |
[33 queries :: 0.03587 seconds ]
|
|
