 |
|
|
|
|
|
|
|
|
|
makboy86
Fordmods Newbie
Posts: 10
Joined: 13 Nov 2004
Location: Australia NSW, Australia
View User Gallery (0)
|
 Posted: Sun Feb 27, 2005 10:56 am Post subject: EF Fuel Pump |
 |
|
Does any one know what the tool is called to get the black ring that sits on the feul pump off. I tried with a hammer and screw driver but 1 of the teeth nearly snaped off?
(if there is a special tool and where can i get it from) |
|
| Back to top |
|
|
|
|
|
|
|
|
|
scotts840
Fordmods Stock as a Rock
Posts: 138
Joined: 04 Feb 2005
Location: your mum's bedroom WA, Australia
View User Gallery (0)
|
| Posted: Sun Feb 27, 2005 12:14 pm Post subject: |
|
|
| anywhere that sells ABW tools. it's the fuel pump removal tool for falcons. costs about $35 |
|
| Back to top |
|
|
|
|
|
|
|
|
|
chunkz
Fordmods - Getting Side Ways
Age:21
Posts: 5314
Joined: 06 Nov 2004
Location: Melbourne, S.E Suburbs VIC, Australia
View User Gallery (4)
|
| Posted: Sun Feb 27, 2005 3:41 pm Post subject: |
|
|
mate
screw driver on the teeth, hammer
smash it two times
go onto the next one
do the whole round then you can do it with hand |
|
| Back to top |
|
|
|
|
|
|
|
|
|
Timmeh
Moderator
Posts: 6782
Joined: 06 Nov 2004
Location: Perth WA, Australia
View User Gallery (4)
|
| Posted: Sun Feb 27, 2005 4:47 pm Post subject: |
|
|
I'm all for brute force and ignorance but Scotty is right. Get the right tool.  |
|
| Back to top |
|
|
|
|
|
|
|
|
|
x-plode
Fordmods Parts Gopher
Donating Member
Age:22
Posts: 90
Joined: 05 Nov 2004
Location: Cuballing WA, Australia
View User Gallery (0)
|
| Posted: Sun Feb 27, 2005 7:27 pm Post subject: |
|
|
| Gregorys manual has destructions on how to make one if you want too, also spray some crc around the cap and let it soak a bit and also undo the lid on the fuel tank to let the pressure out, i got away with not having to use the tool then... After my fuking pump siezed christmas day. |
|
| Back to top |
|
|
|
|
|
|
|
|
|
EF 4.9
Fordmods Stock as a Rock
Posts: 139
Joined: 08 Nov 2004
Location: Meeka, Coonland WA, Australia
View User Gallery (4)
|
| Posted: Mon Feb 28, 2005 10:43 am Post subject: |
|
|
| just make one as per the gregorys manual. should only take 10 minutes, all you need is an angle gringer a peice of flat bar and a bolt, (ust the bolt to go through the middle of the thing instead of gutting a 13mm square hole in it. |
|
| Back to top |
|
|
|
|
|
|
|
|
|
scotts840
Fordmods Stock as a Rock
Posts: 138
Joined: 04 Feb 2005
Location: your mum's bedroom WA, Australia
View User Gallery (0)
|
| Posted: Mon Feb 28, 2005 1:13 pm Post subject: |
|
|
| yeah. i use a home made one. has a dead socket welded to it so i can use a 1/2 drive ratchet on it. we've had it since before the tool was available. but when the tool's that cheap and if you don't own a welder. . . . . |
|
| Back to top |
|
|
|
|
|
|
|
|
|
makboy86
Fordmods Newbie
Posts: 10
Joined: 13 Nov 2004
Location: Australia NSW, Australia
View User Gallery (0)
|
| Posted: Mon Feb 28, 2005 2:17 pm Post subject: |
|
|
| yea i bought the tool from auto 1 40 bucks its lieka claw very good |
|
| Back to top |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
