 |
|
|
|
|
|
|
|
|
|
dc357
Fordmods Stock as a Rock
Posts: 178
Joined: 10 Feb 2008
Location: Gunnedah NSW, Australia
View User Gallery (5)
|
 Posted: Tue May 13, 2008 1:38 pm Post subject: Will XR6 clock fit BA-XT.(Has XT got same loom as XR?) |
 |
|
Will XR6-Fairmont Ghia dash clock fit in 02BA-XT.
Has XT got wiring loom to suit this clock or will a loom need to be purchased? |
|
| Back to top |
|
|
|
|
|
|
|
|
|
xpression
Technical Contributor
Age:23
Posts: 2339
Joined: 07 Nov 2004
Location: Perth WA, Australia
View User Gallery (6)
|
| Posted: Tue May 13, 2008 1:39 pm Post subject: |
|
|
| you will need to wire it in. |
|
| Back to top |
|
|
|
|
|
|
|
|
|
dc357
Fordmods Stock as a Rock
Posts: 178
Joined: 10 Feb 2008
Location: Gunnedah NSW, Australia
View User Gallery (5)
|
| Posted: Tue May 13, 2008 2:13 pm Post subject: ok! |
|
|
Wiring loom at ebay but wants $75+post!
Are they worth that much? |
|
| Back to top |
|
|
|
|
|
|
|
|
|
Lukeyson
Fordmods - Getting Side Ways
Posts: 882
Joined: 07 Nov 2005
Location: Newcastle NSW, Australia
View User Gallery (0)
|
| Posted: Sun May 18, 2008 10:48 pm Post subject: |
|
|
Nope. They are not worth that much.
There is a tech article about it here somewhere. You need:
(a) A PC CDRom Internal audio cable. The end that plugs into the Back of the CDRom is identical to the plug on tha back of the clock.
(b) The intestinal fortitude to find the wires in your loom to jumper the cable to - this is for providing permanent clock power, GND, illumination power and dimming.
To do a 'factory' install requires a High Series BEM (Body Control Module) as this is the module that supplies the power, and an ICC sub-loom from a DZ Climate Control ICC, as this picks up the lines from the BEM and runs them up to the 'CDRom Connector' under the Clock. Changing the BEM immobilises your car though, and requires that a Ford Diagnostic tool be used to conduct a parameter reset. It's all good fun.
Lukeyson |
|
| Back to top |
|
|
|
|
|
|
|
|
|
dc357
Fordmods Stock as a Rock
Posts: 178
Joined: 10 Feb 2008
Location: Gunnedah NSW, Australia
View User Gallery (5)
|
| Posted: Tue May 20, 2008 5:50 pm Post subject: |
|
|
Hmmmmm! all sounds fairly serious just for a clock!
Anyhow thanks for info,
will give it a go. |
|
| Back to top |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
dc357
Fordmods Stock as a Rock
Posts: 178
Joined: 10 Feb 2008
Location: Gunnedah NSW, Australia
View User Gallery (5)
|
| Posted: Wed May 21, 2008 10:01 am Post subject: |
|
|
yeah thanks Nicko, I have found that document & printed it out for future use.
I did contact Jaycar (as source for plug to fit clock) I even sent them the section of that article that mentions the plug & they said they did not have it??????????????  |
|
| Back to top |
|
|
|
|
|
|
|
|
|
fnp
Fordmods - Getting Side Ways
Age:23
Posts: 4224
Joined: 24 Mar 2005
Location: Perth WA, Australia
View User Gallery (3)
|
| Posted: Wed May 21, 2008 10:37 am Post subject: |
|
|
| Any computer shop or self respecting nerd should have tons of those cables sitting around. |
|
| Back to top |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
