 |
|
|
|
|
|
|
|
|
|
|
phantomxr8
Fordmods Parts Gopher
Age:27
Posts: 59
Joined: 08 Nov 2004
Location: Toowoomba QLD, Australia
View User Gallery (3)
|
 Posted: Thu Mar 17, 2005 6:00 pm Post subject: Nitrous on BA XR8 |
 |
|
Im looking at putting nitrous on my xr8 mainly for the strip and dyno. Has any one got any info on having the kit in the car legality wise for QLD , and prices of kits that would be suitable. any help would be great
 Cheers |
|
| Back to top |
|
|
|
|
|
|
|
|
|
EDXR8
Fordmods - Getting Side Ways
Age:29
Posts: 1440
Joined: 07 Nov 2004
Location: Adelaide SA, Australia
View User Gallery (0)
|
| Posted: Thu Mar 17, 2005 9:15 pm Post subject: |
|
|
| Well I don't think Nitrous is legal in any state, you can have it installed in a number of states but the lines must be dissconected. Kits will start at about $1100+ for a standard EFI kit and go upto $2k+ for progressive control etc. Personally I don't like Nitrous, it puts a lot of strain on the engine and contaminates the oil with the by-products causing increased wear. It is great bang for buck but I would put that money into other mods that will give me more power all the time, but thats just me. |
|
| Back to top |
|
|
|
|
|
|
|
|
|
xpression
Technical Contributor
Age:23
Posts: 2339
Joined: 07 Nov 2004
Location: Perth WA, Australia
View User Gallery (6)
|
| Posted: Thu Mar 17, 2005 10:27 pm Post subject: |
|
|
| also it will void your new car warranty.. i guess u already thought of that but just a thought... |
|
| Back to top |
|
|
|
|
|
|
|
|
|
gravelrash
Fordmods Stock as a Rock
Age:32
Posts: 110
Joined: 05 Nov 2004
Location: Dalby QLD, Australia
View User Gallery (0)
|
| Posted: Fri Mar 18, 2005 7:00 am Post subject: |
|
|
sorry to hijack the thread, i see your from Toowoomba and into dyno comps..
Wanna earn $500 in one weekend??
Cruizers Car Club of Dalby
presents
Dalby Dyno Competition
saturday 23rd April
Entry $40.00
Pre-Entry $35
11 Catergories
4cyl Nat Asp & 4cyl Forced Induct.
6cyl Nat Asp & 6cyl Forced Induct.
8cyl Nat Asp & 8cyl Forced Induct.
Rotary Nat Asp & Rotary Forced Induct.
Highest Horsepower 1st & 2nd
Worst Horsepower
$700 in Prize money and trophies
Highest Horsepower 1st place $500
2nd place $200
for more info:
Greg: 0412383090
Ben: 0417076227
Rolly: 0422265913
*nitrous Oxide is classed as forced induction*
No rules, unlimited boost, unlimited fuel type. Just put on a good show. |
|
| Back to top |
|
|
|
|
|
|
|
|
|
phantomxr8
Fordmods Parts Gopher
Age:27
Posts: 59
Joined: 08 Nov 2004
Location: Toowoomba QLD, Australia
View User Gallery (3)
|
| Posted: Fri Mar 18, 2005 5:12 pm Post subject: |
|
|
gravelrash
I already have the entry form sitting on my desk
Cheers  |
|
| Back to top |
|
|
|
|
|
|
|
|
|
TerroristGHIA
Fordmods - Getting Side Ways
Age:36
Posts: 2330
Joined: 25 Nov 2004
Location: Sydney Australia NSW, Australia
View User Gallery (9)
|
| Posted: Sat Mar 19, 2005 8:09 pm Post subject: |
|
|
OK, legalities for NOS on the street are as follows for NSW at least
1 The Kit can be installed no problems
2 the bottle MUST NOT be connected to the kit anytime the vehicle is driven on a public road.
As to how it goes in an E series V8, i personally have a 150 hp dry kit in my Ghia and have no problems with it at all
On going costs 120 for the initial fill, then a max of 120 for every other fill.
Hidden costs- Bigger fuel pump, bigger injectors,special plugs, adjustable fuel reg, upgraded ignition. Similar to a naturally aspirated motor.
My vehicle went from 109rwkw dead stock (143000kms) to 140rwkw with all mods so far, to 219rwkw when the NOS is activated.
It is a great sleeper. If you are worried about fitting it, then dont. Then tuning for mine has amounted to over 3 hrs on the Dyno, with more to come, as a new inlet manifold and coil are about to be fitted, and the unichip will need its last retune for this year. We are looking for 253rwkw solidly with the NOS and 150-160 without. will keep you all advised. I have put over 3000k on the motor since the NOS kit was installed and havent looked back.
Important note to those that want to play with NOS. Ensure your mill is in tip top condition. Do all the mods you would naturally aspirated, then tune it, the fit NOS, then tune it again.
Plugs, coil and mixtures must be spot on. the slightest problem either way will kill your engine. When tuning the NOS kit, start small and work up in baby steps. Make sure your fuel supply is up to scratch. Make sure your ingition system is up to scratch. Be conservative and all will be fine. Read NOS for me on this sight in V8 workshop to see how i did it
Brett |
|
| Back to top |
|
|
|
|
|
|
|
|
|
phantomxr8
Fordmods Parts Gopher
Age:27
Posts: 59
Joined: 08 Nov 2004
Location: Toowoomba QLD, Australia
View User Gallery (3)
|
| Posted: Mon Mar 21, 2005 10:31 am Post subject: |
|
|
Cheers FPV56L very helpful
Looks like the boss will be getting some |
|
| Back to top |
|
|
|
|
|
|
|
|
|
XRCIST
Fordmods Stock as a Rock
Posts: 180
Joined: 08 Nov 2004
Location: Melbourne VIC, Australia
View User Gallery (2)
|
| Posted: Thu Mar 24, 2005 7:31 pm Post subject: |
|
|
Hey guys for more info and how to put it on a ba xr8 check out this article
Go to google, type in autospeed nos ba xr8 and go down and click on the one that says whos da boss. Do it this way to view the whole article
Cheers |
|
| Back to top |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
| |
| (c)2002-2008 Matti Jones and Brad Evans |
[35 queries :: 0.04716 seconds ]
|
|
