|
| Steady ED |
|
|||
|
Not for 4.11s as far as I know.
There was talk of using an XF sender with an XF gear, but that was for 3.9s IIRC. Its a moot point anyway, because if you use the correct gear in the box, your auto shiftpoints will get f**k up. A speedo correcter between the ecu and dash is the only way really.
_________________ ED XR8 Sprint - S-Trim, V500, 249rwkw |
|||
| Top | |
|||
| falcon_3512003 |
|
|||
|
ok cool are they easy to wire in and do you have to make the device from scrach or is it pre made
_________________ now have a series 1 au starting the mods slowly |
|||
| Top | |
|||
| Steady ED |
|
|||
|
Can buy em premade.
Jaycar does them and "66 coupe" on here does them as well I think? Haven't wired one in personally, so cant really comment, but wouldn't be too hard to splice in.
_________________ ED XR8 Sprint - S-Trim, V500, 249rwkw |
|||
| Top | |
|||
| falcon_3512003 |
|
|||
|
ok cool have to chase 1 up tomora see what jaycar has thanks
_________________ now have a series 1 au starting the mods slowly |
|||
| Top | |
|||
| gogetta |
|
|||
|
Steady ED wrote: Gearbox, fairly sure it goes speedo sender > ECU > dash.
Best bet is a speedo corrector between the ECU and dash. wrong it goes sender>dash>ecu
_________________ |
|||
| Top | |
|||
| gogetta |
|
|||
|
falcon_3512003 wrote: ok guys got it all sorted out today cost me 80 buks to have it fitted to my housing and its all good just finished takeing it for a test drive and it has no noises or anything all it was is the pinion bearing was smaller witch made up the 1/4 slack now all i have to do is sort out the speedo lol it still cut when it hit 180
what diff place did u take it to? wouldnt have the bearing part number would u?
_________________ |
|||
| Top | |
|||
| falcon_3512003 |
|
|||
|
keysbourgh diffs in dandynong ask for kelvin if you need it done it was a cash job while the boss wasnt there lol
_________________ now have a series 1 au starting the mods slowly |
|||
| Top | |
|||
| Grimketel |
|
|||
|
administering CPR to this thread.
Im doing a diff gear change on the weekend to 3.89's from an r31. So far Ive gathered that theres issues with pinion shimming, and that a 7 mm shim, or a new bearing can fix this up? Ive got a set of new diff bearings to go on, so will this new pinion bearing sort this problem out? My mate who is putting it together is a mechanic, but hasnt done AU diffs before. Hopefully he can get it going 
then its a case of a speedo adjustment, which I have read about and so far understand the need for 2 modules. However Ive heard you can alter shift points with a flash tuner, which I also have. So can anyone tell me yay or nay if a single speedo corector, and a flash tune with altered shift points will work the same as 2 speedo correctors?
_________________ enough isn't enough |
|||
| Top | |
|||
| Grimketel |
|
|||
|
Ive checked the stampings and the lsd from the EF thats going in has 0578-914
and the diff of unknown type from the r31 has 0578-902 does this mean I will not have any issues with the pinion after all?
_________________ enough isn't enough |
|||
| Top | |
|||
| xfpaul |
|
||
|
same here ,got a set of 0575 gears trying to go into 78 series , the pinion brg thats beeing used to fix this, any no.s and which one is it the pinion end or the flange end?
are 78 gears stronger??
_________________ NC2 Fairlane AU2 Intech 4.0 Wolf V500 ECU Accel 500cc Injectors Eaton M90 Blower MPx Porting 75mm Mustang TB Intercooler Holley 255lph EL XR6 Rear End 3.45 LSD Duel Fuel lots more. |
||
| Top | |
||
| xfpaul |
|
||
|
OK solid info and fitted,
0575 and 0578 gear sets are the same, but if you put 0575 in a 78 housing you have to change the large pinion brg from the small timken no. HM88649 TO THE LARGER HM89446 THE OUTER IS THE SAME FOR BOTH HM89410 all the other brgs and the seal are the same, no spacer required
_________________ NC2 Fairlane AU2 Intech 4.0 Wolf V500 ECU Accel 500cc Injectors Eaton M90 Blower MPx Porting 75mm Mustang TB Intercooler Holley 255lph EL XR6 Rear End 3.45 LSD Duel Fuel lots more. |
||
| Top | |
||
| cjh |
|
|||
|
I woud like to know how much for the centre??????^^^^^^^^^^^^^^^^^^^^.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| cjh |
|
|||
|
falcon_3512003 wrote: do you just wana sell the housing thats all i need I'm interested in the centre, how much ^^^^^^^^^^^^??????
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| revan8_NL |
|
||
Age: 33 Posts: 130 Joined: 21st May 2009 Ride: NL Fairlane Concorde Ghia Location: Adelaide, SA |
Im getting a brand new built diff put in soon, this will alter the speedo reading.
Wont it? I was wondering if there is anywhere any one knows, in SA, that this could be altered and the speedo read correctly with the new diff. Cheers |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 14 guests |
