|
| falcon_3512003 |
|
|||
|
got the 4.11 pintara center all is good with the crown fiting on my center but the pinion seems to bit by about 7mm it wont tighten up anyone had this problem and what did they do aparently there are two tipes of diff housings for the ef's ??
_________________ now have a series 1 au starting the mods slowly |
|||
| Top | |
|||
| stockstandard |
|
|||
|
4.11 pintara is a borg warner 75 series, yours is a borg warner 78. You will need to have a shim made up for the pinion if you want to fit it to your housing
_________________ Stoke me a clipper, I'll be back for Christmas |
|||
| Top | |
|||
| falcon_3512003 |
|
|||
|
do you know what size i have to get the guy i took it to today didnt want to do it and told me to get another housing cause i had the rong one
_________________ now have a series 1 au starting the mods slowly |
|||
| Top | |
|||
| stockstandard |
|
|||
|
its about 1/4". Best bet is to take it to a diff shop and get them to fit and shim it up for you.
_________________ Stoke me a clipper, I'll be back for Christmas |
|||
| Top | |
|||
| falcon_3512003 |
|
|||
|
yer just rang one place he wants 150 to 300 to do it outrages
_________________ now have a series 1 au starting the mods slowly |
|||
| Top | |
|||
| falcon_3512003 |
|
|||
|
there is a colapsable shim allready on the pinion can i add another one to make up the 1/4 needed will that work anyone recon or not??
_________________ now have a series 1 au starting the mods slowly |
|||
| Top | |
|||
| falcon_3512003 |
|
|||
|
seems likt theses not enough pull down on the bolt even when you take out the shim theses still play not as much thow the front bearing has to go in more but theres a mynute step up on the pinion were the shim goes if this wasnt there i recon it mite pull down ok and have a shim between the bearing and sharft yoke anyone figerd this be for ?
_________________ now have a series 1 au starting the mods slowly |
|||
| Top | |
|||
| gogetta |
|
|||
|
in your other post I asked what diff you had...
some diffs are more compatible than others when it comes to ratio changes... whats the car, whats the original housing ratio?
_________________ |
|||
| Top | |
|||
| gogetta |
|
|||
|
searching through another of your posts you say you have a 3.08 diff...
I assume its an EF or EL... well it seems you have the same problem as other people with 3.08s that try to put 3.45 ratio gears in there housings.... ive tried to research this stuff before and it seems to me that the housing itself on the 3.08 diff is different to other housings
_________________ |
|||
| Top | |
|||
| falcon_3512003 |
|
|||
|
yep thats the one
_________________ now have a series 1 au starting the mods slowly |
|||
| Top | |
|||
| falcon_3512003 |
|
|||
|
so whats going to be a compatable housing then for these 4.11 gears
_________________ now have a series 1 au starting the mods slowly |
|||
| Top | |
|||
| gogetta |
|
|||
|
youll need a the 3.23 ratio housing as a start I believe...
 actually i have a 3.23 EF LSD diff if your interested $200
_________________ |
|||
| Top | |
|||
| gogetta |
|
|||
|
ask a few people that have done it what their ratios were originally
_________________ |
|||
| Top | |
|||
| falcon_3512003 |
|
|||
|
do you just wana sell the housing thats all i need
_________________ now have a series 1 au starting the mods slowly |
|||
| Top | |
|||
| gogetta |
|
|||
|
ive got a housing from a from a EL its got a NON lsd 3.45 ratio centre of all things!
id want a $100 for it
_________________ |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 25 guests |
