Fordmods Logo

rotor removal from an ef asap 

 

Page 1 of 1 [ 6 posts ] 

 
 Post subject: rotor removal from an ef asap
Posted: Sun May 27, 2012 12:04 pm 
Parts Gopher
Offline

Age: 27

Posts: 65

Joined: 19th Jan 2012

Gallery: 2 images

Ride: ford falcon futura

Location: Newcastle
NSW, Australia

hey guys, i would do a serch but i have no time atm, iv got untill this arvo to figure out how to remove brake rotors ( front and pack ) of a ef fairmont, im going out to my mums brithday lunch now ( thus why i dont have time to serch ) and i will be checking this post threw out the day. i have never removed them before so any help would be much loved :)
Top
 Profile  
 
 
 Post subject: Re: rotor removal from an ef asap
Posted: Sun May 27, 2012 12:12 pm 
Getting Side Ways
Offline
User avatar

Age: 25

Posts: 4599

Joined: 30th Aug 2010

Ride: BF XR6,

Location: NEWCASTLE
NSW, Australia

where abouts in newcastle do you live mate? i can do it piece of piss, i do have to work soon but if you live near by i can lend a hand on 1 side

 

_________________

BF XR6
xr8 snorkel,typhoon lower snorkel,territory intake pipe,20% underdrive kit,pacemaker extractors,high flow cat,xforce exhaust,t56 conversion hd turbo clutch/ flywheel,m86 3.45 lsd,custom tune187.1rwkw as an auto

Top
 Profile  
 
 
 Post subject: Re: rotor removal from an ef asap
Posted: Sun May 27, 2012 12:15 pm 
Getting Side Ways
Offline
User avatar

Age: 25

Posts: 3355

Joined: 10th Jan 2010

Gallery: 8 images

Ride: EL XR6

Location: albion park, wollongong
NSW, Australia

Front

To get the front caliper off there are 2 bolts holding it on the upright, behind the rotor . Once the caliper is off there's a cap in the centre of the rotor . Get a screwdriver and hammer and pry and tap if off , clean the grease off the stub and take out the split pin and undo tge nut should be finger tight , use a 15" shifter or multi grips . Then slide off the washer and the rotor will slide off the stub ,

Rear is much the same with the calipers, except the rotor will slide off the studs , give it a good tap with a hammer to free it , I think there's a bolt or screw under a rubber grommet which you have to remove to allow the rotor to slide off . Could be wrong been years side I did rears .

 

_________________

El XR6 Turbo
Dark Agents,Sunroof, bilstein shocks, 6000k HIDS, 329 mm slotted rotors, twin pot calipers , Climate Control, GarrettT04 turbo,log manifold, crow turbo cam, microtech lt10c, 42lb injectors , 044, surge tank , T56 , rebuilt bottom end , alloy plenum .

Aiming for 300 rwkw

Top
 Profile  
 
 
 Post subject: Re: rotor removal from an ef asap
Posted: Sun May 27, 2012 12:24 pm 
Parts Gopher
Offline

Age: 27

Posts: 65

Joined: 19th Jan 2012

Gallery: 2 images

Ride: ford falcon futura

Location: Newcastle
NSW, Australia

i live in newcastle but im getting the rotors off a car near morriset, wont be heading down till around 2:30 assuming the guy will still give me the parts! im not 100% sure he will now.
Top
 Profile  
 
 
 Post subject: Re: rotor removal from an ef asap
Posted: Sun May 27, 2012 12:28 pm 
Getting Side Ways
Offline
User avatar

Age: 25

Posts: 4599

Joined: 30th Aug 2010

Ride: BF XR6,

Location: NEWCASTLE
NSW, Australia

ok sorry man i start work at 3

 

_________________

BF XR6
xr8 snorkel,typhoon lower snorkel,territory intake pipe,20% underdrive kit,pacemaker extractors,high flow cat,xforce exhaust,t56 conversion hd turbo clutch/ flywheel,m86 3.45 lsd,custom tune187.1rwkw as an auto

Top
 Profile  
 
 
 Post subject: Re: rotor removal from an ef asap
Posted: Sun May 27, 2012 9:18 pm 
Parts Gopher
Offline

Age: 27

Posts: 65

Joined: 19th Jan 2012

Gallery: 2 images

Ride: ford falcon futura

Location: Newcastle
NSW, Australia

got the front ones off with out to much trouble, didnt bother with the back ones though. thank you for your help :)
Top
 Profile  
 
Display posts from previous:
Sort by  
 Page 1 of 1  [ 6 posts ] 

Who is online

Users browsing this forum: No registered users and 13 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

 

 

It is currently Fri Dec 15, 2017 12:26 am All times are UTC + 11 hours

 

 

(c)2014 Total Web Solutions Australia - Australian Web Hosting and Domain Names