Fordmods Logo

Intake Air Temp Sensor Relocation 

 

Page 1 of 1 [ 13 posts ] 

 
 Post subject: Intake Air Temp Sensor Relocation
Posted: Sun Aug 08, 2010 10:19 pm 
Getting Side Ways
Offline
User avatar

Age: 39

Posts: 2282

Joined: 14th Jan 2005

Gallery: 8 images

Ride: ED Fairmont Ghia & EF XR8

Location: Melbourne
VIC, Australia

coming up to the final stages of finishing the gt40p/explorer manifold install on the ef and im undecided as to where im going to put the ait sensor.

originally i was going to have a bung welded and a thread tapped on the intake tube (3" stainless steel) as per the au's but then i remembered working on a my brothers vt and noticing that it has the air charge sensor plugged into a hole on the air box lid.

i like the idea of it being in the upper air box as it will take 5min max to drill a hole and look a hell of a lot cleaner as opposed to a few days wait while i have someone weld a bung and tap a thread in the intake tube not mention the $100 plus labour charge.

cheers in advance for any replies

 

_________________

Image

Top
 Profile  
 
 
 Post subject: Re: Intake Air Temp Sensor Relocation
Posted: Sun Aug 08, 2010 11:42 pm 
Smokin em up
Offline

Age: 70

Posts: 224

Joined: 31st May 2010

Gallery: 3 images

Ride: XF 5 LIT P/ VAN EF 5 LIT FUTURA

Location: melbourne
VIC, Australia

I put mine in the intake manifold as per std. But I got it welded at work for nothing. Should be ok in the intake as per AU. Holden's run in the air box lid. Manifold is probably thick enough to just drill & tap. I just put one in a tunnel ram that way & it worked fine. Regards TPVM.

 

_________________

SALT IS FOR RACING ON. SAUCE IS FOR FISH & CHIPS.

Top
 Profile  
 
 
 Post subject: Re: Intake Air Temp Sensor Relocation
Posted: Mon Aug 09, 2010 12:22 pm 
Getting Side Ways
Offline

Posts: 2464

Joined: 5th Nov 2004

Gallery: 7 images

Location: Brisbane
QLD, Australia

Alan - where abouts did you put yours on the AU Manifold?

Nigel
Top
 Profile  
 
 
 Post subject: Re: Intake Air Temp Sensor Relocation
Posted: Mon Aug 09, 2010 3:44 pm 
Getting Side Ways
Offline

Posts: 699

Joined: 1st Jan 2006

Ride: Lots, all Fords

Location: Hamilton
New Zealand

Depending on which ecu your engine runs, moving the IAT sensor to the AU location in the inlet tube may inhibit adaptive learning under certain ambient conditions (low temp) as the minimum ACT will never be reached. They were often set to a minimum of 100°F = 38°C to allow for the intake charge heating through the manifold. The minimum set point can be changed but requires a chip.

 

_________________

XA Faimont 351C, AU2 XR8 Manual 5.0, DA LTD 5.0, Mk1 Capri 5.0, 1995 Mustang 5.0, EF2 XR8 Manual, EF2 Fairmont Ghia 5.0, AU3 XR8 Auto, AU2 XR8 Auto, AU2 XR8 Manual Ute, TE Cortina 5.0 Manual, DU LTD 5.0 soon to be manual

Top
 Profile  
 
 
 Post subject: Re: Intake Air Temp Sensor Relocation
Posted: Mon Aug 09, 2010 11:38 pm 
Smokin em up
Offline

Age: 70

Posts: 224

Joined: 31st May 2010

Gallery: 3 images

Ride: XF 5 LIT P/ VAN EF 5 LIT FUTURA

Location: melbourne
VIC, Australia

Good to know that. I fitted mine in the same place as EF one's are. Regards Alan TPVM.

 

_________________

SALT IS FOR RACING ON. SAUCE IS FOR FISH & CHIPS.

Top
 Profile  
 
 
 Post subject: Re: Intake Air Temp Sensor Relocation
Posted: Tue Aug 10, 2010 10:05 am 
Getting Side Ways
Offline

Posts: 2464

Joined: 5th Nov 2004

Gallery: 7 images

Location: Brisbane
QLD, Australia

So you just tapped #5?

Nigel
Top
 Profile  
 
 
 Post subject: Re: Intake Air Temp Sensor Relocation
Posted: Tue Aug 10, 2010 12:54 pm 
Smokin em up
Offline

Age: 70

Posts: 224

Joined: 31st May 2010

Gallery: 3 images

Ride: XF 5 LIT P/ VAN EF 5 LIT FUTURA

Location: melbourne
VIC, Australia

I did weld a boss on. But you probably could just tap it. Regards Alan TPVM.

 

_________________

SALT IS FOR RACING ON. SAUCE IS FOR FISH & CHIPS.

Top
 Profile  
 
 
 Post subject: Re: Intake Air Temp Sensor Relocation
Posted: Wed Aug 11, 2010 2:28 am 
Getting Side Ways
Offline

Age: 54

Posts: 419

Joined: 16th Jan 2005

Ride: EF Ghia 5.0

Location: Adelaide
SA, Australia

xafalcon wrote:
Depending on which ecu your engine runs, moving the IAT sensor to the AU location in the inlet tube may inhibit adaptive learning under certain ambient conditions (low temp) as the minimum ACT will never be reached. They were often set to a minimum of 100°F = 38°C to allow for the intake charge heating through the manifold. The minimum set point can be changed but requires a chip.


That's good info. I have mine mounted where the dog turd used to be and the car usually runs a bit lumpy most of the time. I did notice that in hot weather, the car runs a LOT better than when it was in the manifold. I might swap it back there in colder weather and see what happens.

Mike

 

_________________

EF Ghia 5.0 - XR8 in a tuxedo....classy, low and loud

Bordeaux Purple, Tickford kit, slammed, 18" BA XR8's, EL Ghia chrome, full leather, Pioneer audio, C&C, ABS, LSD, Crane cam, GT40P heads, high flow cats, Genie extractors, lots of woodgrain, chrome and interior lights!

Top
 Profile  
 
 
 Post subject: Re: Intake Air Temp Sensor Relocation
Posted: Wed Aug 11, 2010 11:29 am 
Getting Side Ways
Offline
User avatar

Age: 39

Posts: 2282

Joined: 14th Jan 2005

Gallery: 8 images

Ride: ED Fairmont Ghia & EF XR8

Location: Melbourne
VIC, Australia

xafalcon wrote:
Depending on which ecu your engine runs, moving the IAT sensor to the AU location in the inlet tube may inhibit adaptive learning under certain ambient conditions (low temp) as the minimum ACT will never be reached. They were often set to a minimum of 100°F = 38°C to allow for the intake charge heating through the manifold. The minimum set point can be changed but requires a chip.


off the top off my head its a 4ddf ecu (ef s1). after all mods are done and dusted i had planned to book it in to either bluepower or electronic automotive for a tune.

from what i understand from your post is that it will be fine to put the sensor in the intake tube or the upper lid so long as the car is tuned accordingly

cheers

 

_________________

Image

Top
 Profile  
 
 
 Post subject: Re: Intake Air Temp Sensor Relocation
Posted: Wed Aug 11, 2010 11:40 am 
Getting Side Ways
Offline

Posts: 2464

Joined: 5th Nov 2004

Gallery: 7 images

Location: Brisbane
QLD, Australia

That will all depend on your tuner - some will go the extra mile (and change the learn windows). Most wont - hobbyists will. Most tuners will focus on your tunes themselves, and wont be concerned about the self-learn functions.

Nigel
Top
 Profile  
 
 
 Post subject: Re: Intake Air Temp Sensor Relocation
Posted: Wed Aug 11, 2010 12:37 pm 
Getting Side Ways
Offline
User avatar

Age: 39

Posts: 2282

Joined: 14th Jan 2005

Gallery: 8 images

Ride: ED Fairmont Ghia & EF XR8

Location: Melbourne
VIC, Australia

Nigel wrote:
That will all depend on your tuner - some will go the extra mile (and change the learn windows). Most wont - hobbyists will. Most tuners will focus on your tunes themselves, and wont be concerned about the self-learn functions.

Nigel


fair enough, so it's best to request that they look at the self learn windows and adjust them to suit when i book it in.

 

_________________

Image

Top
 Profile  
 
 
 Post subject: Re: Intake Air Temp Sensor Relocation
Posted: Wed Aug 11, 2010 12:40 pm 
Getting Side Ways
Offline

Posts: 2464

Joined: 5th Nov 2004

Gallery: 7 images

Location: Brisbane
QLD, Australia

depends on if they know that much about it...

If your a tuner youd typically only worry about the maps, where they are and how to adjust them.

You may get more bang for your buck doing your own J3 chip....
Top
 Profile  
 
 
 Post subject: Re: Intake Air Temp Sensor Relocation
Posted: Wed Aug 11, 2010 7:52 pm 
Getting Side Ways
Offline

Posts: 699

Joined: 1st Jan 2006

Ride: Lots, all Fords

Location: Hamilton
New Zealand

Most ecu binary definitions don't include many of the adaptive learning functions, none of my EF-EL ones do. But they are all closely based on the original A9L code. And since the factory AIT sensor location for the EF V8 (all E-series V8's in fact) is the same as 89-93 Mustangs with the A9L ecu, it is highly likely that the same minimum value (100°F) remains.

My advise is to mount the IAT as close to the original E-series location as possible.

 

_________________

XA Faimont 351C, AU2 XR8 Manual 5.0, DA LTD 5.0, Mk1 Capri 5.0, 1995 Mustang 5.0, EF2 XR8 Manual, EF2 Fairmont Ghia 5.0, AU3 XR8 Auto, AU2 XR8 Auto, AU2 XR8 Manual Ute, TE Cortina 5.0 Manual, DU LTD 5.0 soon to be manual

Top
 Profile  
 
Display posts from previous:
Sort by  
 Page 1 of 1  [ 13 posts ] 

Who is online

Users browsing this forum: No registered users and 20 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

 

 

It is currently Thu Mar 28, 2024 9:01 pm All times are UTC + 11 hours

 

 

(c)2014 Total Web Solutions Australia - Australian Web Hosting and Domain Names