Fordmods Logo

Help needed fitting wastegate actuator ba xr6t 

 

Page 1 of 1 [ 6 posts ] 

 
 Post subject: Help needed fitting wastegate actuator ba xr6t
Posted: Wed Aug 04, 2010 6:24 pm 
Fordmods Newbie
Offline

Age: 39

Posts: 9

Joined: 14th Jun 2010

Ride: ba xr6 turbo ute

Location: rockhampton
QLD, Australia

After many $$$ and ppl telling me i need to re-flash my ba xr6t ECU i went to work myself tryin to find out my over boosting problem, found that my wastegate actuator wouldnt hold preasure. have bourt a new one but been advised its extemely hard to fit with out removing the engine mount or turbo itself. if anyome has fitted one or knows any tricks it would be much appreciated. cheers
Top
 Profile  
 
 
 Post subject: Re: Help needed fitting wastegate actuator ba xr6t
Posted: Thu Aug 05, 2010 9:02 am 
Getting Side Ways
Offline
User avatar

Age: 39

Posts: 862

Joined: 8th May 2005

Ride: BA Wagon Turbo, Ba Fairlane G220

Location: Colac
VIC, Australia

Hey mate I had the same problem had to replace mine last week.

What a pain in the a*** of a job it is, but it can be done without taking the turbo or engine mount off. It is pritty straight forward taking the old one off and putting the new one in. The hard part is trying to put the arm back on, what I did was loosen the actuator bracket I actually took 2 bolts out planning on taking the whole bracket off but it is just too hard to get to the last bolt so I loosened it about half way (took ages just to do that) then I was able to get the arm back on that way. The hard part is trying to hold the wastegate flap closed while you try and get the arm in the right spot. What I ended up having to do was sit on top of the motor and reach in down behind the turbo to hold the flap closed and with your other hand in front of the turbo (I think it was there but somewhere were you can move the arm, its real hard to get at it) try and line up the arm with the flap you have to go by feel as you have no hope of seeing what you are doing, and forget about trying to put the little C clip thing back on that holds the arm in place I had no hope I just ended up using an R clip works well.

Obviously there is more to it but that's the hardest bit you will have to get under the car to get to some bolts and take all the pipes and shielding off.

 

_________________

Congo Green Ba Wagon With F6 6 Speed Manual Driveline.

Top
 Profile  
 
 
 Post subject: Re: Help needed fitting wastegate actuator ba xr6t
Posted: Thu Aug 05, 2010 4:45 pm 
Fordmods Newbie
Offline

Age: 39

Posts: 9

Joined: 14th Jun 2010

Ride: ba xr6 turbo ute

Location: rockhampton
QLD, Australia

sounds like you have it sused, had alook at it today on a hoist so hard to even get at top mounting nut, still have all my heat guards on, so carnt really see much, could you get to the c clip from the top with the guards off? and what was the benfits of loosing that bracket?cheers
Top
 Profile  
 
 
 Post subject: Re: Help needed fitting wastegate actuator ba xr6t
Posted: Thu Aug 05, 2010 5:33 pm 
Getting Side Ways
Offline
User avatar

Age: 39

Posts: 862

Joined: 8th May 2005

Ride: BA Wagon Turbo, Ba Fairlane G220

Location: Colac
VIC, Australia

reidy_08 wrote:
sounds like you have it sused, had alook at it today on a hoist so hard to even get at top mounting nut, still have all my heat guards on, so carnt really see much, could you get to the c clip from the top with the guards off? and what was the benfits of loosing that bracket?cheers


Nah had to get to the c clip from underneath the car with a screw driver and just popped it off. The benefit of loosing the bracket was that it gives you more movement with the arm of the actuator so it is alot easier to get the whole over the pin.

 

_________________

Congo Green Ba Wagon With F6 6 Speed Manual Driveline.

Top
 Profile  
 
 
 Post subject: Re: Help needed fitting wastegate actuator ba xr6t
Posted: Wed Aug 11, 2010 8:26 pm 
Fordmods Newbie
Offline

Age: 39

Posts: 9

Joined: 14th Jun 2010

Ride: ba xr6 turbo ute

Location: rockhampton
QLD, Australia

thanx man, might have a crack at it this weekend let you know how i go. :)
Top
 Profile  
 
 
 Post subject: Re: Help needed fitting wastegate actuator ba xr6t
Posted: Tue Jul 15, 2014 8:26 pm 
Getting Side Ways
Offline

Age: 51

Posts: 443

Joined: 12th Apr 2010

Ride: 2006 BF XR8 Boss 260

Location: Auckland
New Zealand

Super easy when you remove down pipe!

 

_________________

Current...
XY Faker Project...
EL XR6 Work Hack...

Top
 Profile  
 
Display posts from previous:
Sort by  
 Page 1 of 1  [ 6 posts ] 

Who is online

Users browsing this forum: No registered users and 10 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

 

 

It is currently Fri Mar 29, 2024 10:22 am All times are UTC + 11 hours

 

 

(c)2014 Total Web Solutions Australia - Australian Web Hosting and Domain Names