Fordmods Logo

Reading spark plugs 

 

Page 1 of 1 [ 3 posts ] 

 
 Post subject: Reading spark plugs
Posted: Sat Dec 30, 2017 12:11 pm 
Getting Side Ways
Offline

Posts: 852

Joined: 1st Apr 2005

Gallery: 4 images

Ride: EF XR6 Wagon, AU2 XR6 VCT

Power: 148 rwkw

Location: Auckland
New Zealand

The engine in my AU2 VCT XR6 is factory except for exhaust and induction. It has 269,000 kms on it, has been well-maintained, and runs beautifully - pulls hard, runs smooth, burns no oil, and the oil doesn't turn dark.

This isn't a problem, more just a curiosity.

I have just replaced the Bosch WR9LCX+ spark plugs with Autolite 985s. The Bosch plugs have probably 25,000 kms on them and look good - the insulator is near-white on one side, tan/grey/brown on the other. I have read that you can tell if you have the right heat range by where the colour changes on the side electrode - ideally, the colour should change at the bend. The attached pic shows three of the Bosch plugs with widely varying colour change points: one near the tip, one in the middle, and one at the base. That indicates that the three are operating at very different temperatures in the one engine - or, that the spark plugs have different heat ranges. What can cause this?

Variation in fuel injector flow rates? I don't have a reliable compression tester, but seriously doubt that compression is the problem, as the engine is as strong as ever and uses no oil. The coilpack and ignition leads are near new and tested well in spec for resistance. There are no symptoms of anything remotely wrong with the engine, as it's running sweet.

Production tolerances in the plugs might be the culprit, but that would be surprising for German-made plugs. The insulator shape determines the heat range, so how likely is it that they used the wrong insulator? I did notice that one of the plugs had the threads cut poorly, as it was very tight going in and out, even with anti-seize; an Autolite plug went into the same hole just fine. So maybe Bosch quality isn't what it once was.

Thanks for your help.

 

 

Attachments:
PC280007b.jpg
PC280007b.jpg [ 486.69 KiB | Viewed 79 times ]

 

_________________

95 EF XR6 wagon, 17" FTRs, DBA, QFM, KYB/Koni, AU block, ported 4-angled EF XR6 head, SS Inductions, Territory intake, 10:1 CR, Auckland 1258 cam, Coby headers, no cat, Tickford 2.5", 2850rpm stall, J3 chip

Top
 Profile  
 
 
 Post subject: Re: Reading spark plugs
Posted: Mon Jan 01, 2018 12:15 am 
Getting Side Ways
Offline
User avatar

Age: 65

Posts: 3550

Joined: 11th Jan 2009

Ride: BA Falcon XT

Location: Smithfield
NSW, Australia

I have used the FORD plugs for a long time and to be honest, never had a REAL issue with them.
The last time I remember a HUGE problem with the Ford plugs was for the EA/EB.

I sold HEAPS of the Ford ones for EF/EL/AU/BE/FG and don't remember many issues with them.
Top
 Profile  
 
 
 Post subject: Re: Reading spark plugs
Posted: Tue Jul 03, 2018 4:25 am 
Fordmods Newbie
Offline
User avatar

Posts: 7

Joined: 30th Jul 2011

Ride: EF Fairmont Ghia

Location: Sydney
NSW, Australia

I would guess they look different because they have a different rotation when installed. I don't think all threads start at the same point on heads nor on the plugs, so they sit pointing in different directions. Racers actually use shims to get them into optimal position so the turbulence of the incoming mixture doesn't blow away the spark. Or something. In any case, they look ok in all respects.
Top
 Profile  
 
Display posts from previous:
Sort by  
 Page 1 of 1  [ 3 posts ] 

Who is online

Users browsing this forum: No registered users and 14 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
cron

 

 

It is currently Wed Dec 12, 2018 3:00 am All times are UTC + 11 hours

 

 

(c)2014 Total Web Solutions Australia - Australian Web Hosting and Domain Names