|
| lukecd |
|
||
|
Heres my new 98 EL XR6 5 speed,
BA XR8 wheels King Springs (lows) Pacemaker Extractors With a full 3 inch exhaust threw.. High Compression pistons Lumpy cam Big valves Got some "head work" done, Not quite sure what but i am guessing somewhere along the lines of Bigger Ports. When i get a bit of money i am looking to get it put onto gas and to have a dyno tune to get the maximum power out of it as possible! Not sure if i am allowed all this while i am on my "P's" but im sure if i dont attract the police i will be fine. If you have any questions or thoughts on what i could also do to my car please let me know. Thanks for looking! You do not have the required permissions to view the files attached to this post.
_________________ EL XR6- 18'' BA XR8 wheels-King Springs-Pacemaker Extractors With a full 3'' exhaust threw..-High Compression pistons-Lumpy cam-Big valves-"head work"-3.45LSD-FPV short throw shifter-Fusion 1000w sub&fusion 350w amp |
||
| Top | |
||
| ef_falcon_95 |
|
|||
|
nice el mate.i love that blue. i was going to get a blue one with rims like urs but it was overpriced and had rust in the sill.
u could install a ba intake. looks better 
_________________ El XR6 Turbo |
|||
| Top | |
|||
| lukecd |
|
||
|
Whats involved in installing that mate? How much am i looking at?
_________________ EL XR6- 18'' BA XR8 wheels-King Springs-Pacemaker Extractors With a full 3'' exhaust threw..-High Compression pistons-Lumpy cam-Big valves-"head work"-3.45LSD-FPV short throw shifter-Fusion 1000w sub&fusion 350w amp |
||
| Top | |
||
| ef_falcon_95 |
|
|||
|
It cost $50 from FTG it's a site sponsor , look on my build thread it's in there .
Basically the ba pipe ends 70mm before the airbox. So I used 3" pipe to join it. But the el airbox is 55mm so I used a ef one. Just undo the 4 bolts. Then u have to plug the breather on it .
_________________ El XR6 Turbo |
|||
| Top | |
|||
| lukecd |
|
||
|
Do you get much more power out of it?
_________________ EL XR6- 18'' BA XR8 wheels-King Springs-Pacemaker Extractors With a full 3'' exhaust threw..-High Compression pistons-Lumpy cam-Big valves-"head work"-3.45LSD-FPV short throw shifter-Fusion 1000w sub&fusion 350w amp |
||
| Top | |
||
| ef_falcon_95 |
|
|||
|
Not really but looks better , and is good if u have a bigger cam. Let's it breathe more
_________________ El XR6 Turbo |
|||
| Top | |
|||
| plper1 |
|
||
|
Hey man,
I got an EL XR6 as well, you could install AU injectors, they dont give you any more power, but you will find that that car is a bit more responsive. Another thing that would really make a difference would be to get a J3 chip from T.I. performance. I put one in about 4 weeks ago, and I'll have to say that it really makes a difference. The car pulls alot harder and it isnt sluggish at bottom end. |
||
| Top | |
||
| lukecd |
|
||
|
Just fitting my new Fusion 12'' sub and fusion 350w 2 channel amp to run it!
After i mounted the amp i thought the cables looked s**t hanging out around the mount to i cut holes in the mount so it would look much nicer.. Also am putting in my Short throw shifter this arvo, Will hopefully have photos up tonight. You do not have the required permissions to view the files attached to this post.
_________________ EL XR6- 18'' BA XR8 wheels-King Springs-Pacemaker Extractors With a full 3'' exhaust threw..-High Compression pistons-Lumpy cam-Big valves-"head work"-3.45LSD-FPV short throw shifter-Fusion 1000w sub&fusion 350w amp |
||
| Top | |
||
| ef_falcon_95 |
|
|||
|
Very neat install , is the sub held into position so it don't slide around , that's something I might look into doing
Good luck with the shifter install
_________________ El XR6 Turbo |
|||
| Top | |
|||
| lukecd |
|
||
|
Yeah mate i put "L" brackets in to hold it in place..
Also, i put the shifter in, nice tight shifts, But it seems to let a lot of noise threw.. Does yours do the same? Its like it needs a rubber seal around the base of it like the old one had?..
_________________ EL XR6- 18'' BA XR8 wheels-King Springs-Pacemaker Extractors With a full 3'' exhaust threw..-High Compression pistons-Lumpy cam-Big valves-"head work"-3.45LSD-FPV short throw shifter-Fusion 1000w sub&fusion 350w amp |
||
| Top | |
||
| ef_falcon_95 |
|
|||
|
Yeah mate mine let's noise in. I put all the rubber bots back on that came off and its still noisy , but yeah I know the rubber boot Ur talking about . The one on the stock shifter, come to mention it my hasn't been noisy lately so I must be used to it.
Are u using the positive stops ?
_________________ El XR6 Turbo |
|||
| Top | |
|||
| lukecd |
|
||
|
Na im not mate because i could get them in as the body work is in the way..
I am going to try and find a rubber thing i can put around the base of the shifter to try and stop noice getting in because it is bloody annoying! haha
_________________ EL XR6- 18'' BA XR8 wheels-King Springs-Pacemaker Extractors With a full 3'' exhaust threw..-High Compression pistons-Lumpy cam-Big valves-"head work"-3.45LSD-FPV short throw shifter-Fusion 1000w sub&fusion 350w amp |
||
| Top | |
||
| ef_falcon_95 |
|
|||
|
Yeah it's fair noisy Ay lol
Especially in 2nd
_________________ El XR6 Turbo |
|||
| Top | |
|||
| lukecd |
|
||
|
Hear is some photos of the short throw shifter i put in today, Makes the driving the car so much better, shifts are really tight and hard..
Need to look at getting a custom rubber boot to put over the shifter base as i think its letting a little bit of air threw and is annoying the S*&t out of me! But all in all i am happy with it and money well spent! You do not have the required permissions to view the files attached to this post.
_________________ EL XR6- 18'' BA XR8 wheels-King Springs-Pacemaker Extractors With a full 3'' exhaust threw..-High Compression pistons-Lumpy cam-Big valves-"head work"-3.45LSD-FPV short throw shifter-Fusion 1000w sub&fusion 350w amp |
||
| Top | |
||
| Jonathan Kakousidis |
|
|||
|
nice car
nice shifter too what brand and how much that set ya back and are they pretty easy to install keen on one for my xr
_________________ MY BABIES |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 11 guests |
