|
| EL2XR8 |
|
|||
|
you mean the pipe between the t/b & maf?
are these available from somewhere as a stock item or are they custom jobs per order? cheers.
_________________ EL II XR8
|
|||
| Top | |
|||
| Scaffy |
|
|||
|
Just go to any exhaust shop and get them to use a 60degree bend, then cut to suit. It takes all of 5 minutes. Then go to an accessory store and get a couple of clamps then fit it up.
_________________ Trickflow Street Heat top end kit, 70mm BBK TB & EGR, 24lb injectors, Underdrives & 3.73s: 275rwhp - 13.15@105mph NA / 12.37@116mph N20 |
|||
| Top | |
|||
| Bsjenko |
|
|||
|
what was the part numbersw on the MSD stuff?
MSD8456 for the dizzy? what about rotor? cheers BEN
_________________ The Lane Lives.... Finally!!!! |
|||
| Top | |
|||
| EL2XR8 |
|
|||
|
Scaffy wrote: Just go to any exhaust shop and get them to use a 60degree bend, then cut to suit. It takes all of 5 minutes. Then go to an accessory store and get a couple of clamps then fit it up.
Ok thanks, so what about the little U turn peice that runs off it about half way along? What's it do and can it be safely cancelled out?
_________________ EL II XR8
|
|||
| Top | |
|||
| Timmeh |
|
||
|
Cap is 8408
Rotor is 8070 Coil is 8227 I didn't get a distributor its just the cap. |
||
| Top | |
||
| Timmeh |
|
||
|
Disco Frank wrote: NICE IDEA SCAFFY!
and pete im sure a nice vortech woudl go sweet  Nah no centrifugal for me. I'd go twin screw if I was going to do it at all. |
||
| Top | |
||
| Bsjenko |
|
|||
|
cheers matey, will be getting the lot shortly, just saves me searching around for part numbers.
_________________ The Lane Lives.... Finally!!!! |
|||
| Top | |
|||
| Timmeh |
|
||
|
EL2XR8 wrote: Scaffy wrote: Just go to any exhaust shop and get them to use a 60degree bend, then cut to suit. It takes all of 5 minutes. Then go to an accessory store and get a couple of clamps then fit it up. Ok thanks, so what about the little U turn peice that runs off it about half way along? What's it do and can it be safely cancelled out? I think it is a resonator that kind of acts like a capacitor to absorb sudden changes in air flow with dramatic changes in throttle position. |
||
| Top | |
||
| BOTTLEDUP |
|
|||
|
Timmeh wrote: EL2XR8 wrote: Scaffy wrote: Just go to any exhaust shop and get them to use a 60degree bend, then cut to suit. It takes all of 5 minutes. Then go to an accessory store and get a couple of clamps then fit it up. Ok thanks, so what about the little U turn peice that runs off it about half way along? What's it do and can it be safely cancelled out? I think it is a resonator that kind of acts like a capacitor to absorb sudden changes in air flow with dramatic changes in throttle position. Pete is right, the little dongle's main function is to help reduce reversion up the intake pipe. Engine bay is looking good there, about all i can suggest is a nice set of MSD leads, 
_________________ TE50 T1 P01 |
|||
| Top | |
|||
| Scaffy |
|
|||
|
^^^ LOL He said dongle!
^^^
_________________ Trickflow Street Heat top end kit, 70mm BBK TB & EGR, 24lb injectors, Underdrives & 3.73s: 275rwhp - 13.15@105mph NA / 12.37@116mph N20 |
|||
| Top | |
|||
| Disco Frank |
|
|||
|
Scaffy wrote: ^^^ LOL He said dongle!
^^^whats wrong with dongle? boobs
_________________ RIP SCOTT |
|||
| Top | |
|||
| NickosELXR |
|
||
|
I know this thread is old as, just wondering if Timmeh has had the chance to run his car down the 1/4 mile yet. Keen to see what 193rwkw in an E-series equates to!! Good work with the car.
_________________ ELXR8 series 1. |
||
| Top | |
||
| Timmeh |
|
||
|
Have no fear it will be run down the 1/4 in approximately 3 weeks next Wednesday.
I'm on late shift for two weeks so that rules me out for 2 then on the 3rd week I'll be there to give it a squirt. I'm dialling in a 14 second flat pass. If I got that I'd be a happy man. Mainly cause the driver has improved. If I still suck then I think a 14.5 will be good. Thanks for the interest. I'll post up the time slip when it comes in.
|
||
| Top | |
||
| NickosELXR |
|
||
|
Have been keeping a keen eye on this one as Im pretty much doin the same thing...GT40p, explorer and a near factory type cam, I hope I get near or as good as your results, Im getting the heads serviced now. But keep us all updated on the time slips- Im sure you'll get a better time then 14.5...good luck.
_________________ ELXR8 series 1. |
||
| Top | |
||
| Steady ED |
|
|||
|
If you can get it off the line I reckon flat 14s shouldn't be a drama. Maybe even dip a bit lower
Good luck Timmeh!
_________________ ED XR8 Sprint - S-Trim, V500, 249rwkw |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 6 guests |
