|
| efun |
|
||
|
Ok guys.. so i'm buying these lights for my ba xt:
 and im just wondering how to install them... and is it easy? how many wires/plugs are there?.. just a matter of taking out the old and plugging this one in? or what's the go? 
_________________ Holden = Hope Our Luck Doesn't End Now |
||
| Top | |
||
| Fairmont_03_5.4 |
|
|||
|
Hey Mate,
Easy job, should take 5-10 mins. There are two screws obviously behind the boot lid. But behind the boot garnish there is one threaded rod with a nut on it for each tail light. Undo the nut and the two screws and pull it straight back, bang your done. You dont need to unplug it, just twist the globes and they will fall out.
_________________ Chaos, Panic and Disorder. My work here is finally done. |
|||
| Top | |
|||
| frd906n |
|
||
|
Are they LEDS
_________________ Daily Driver, Series 1 Au Forte Quote: Posted by Xcabbi, Does it slap or rattle? Rattle is more to do with timing chains and tensioners. Slap is more to do with lifters, rings, bearings or GENIII boat anchors
|
||
| Top | |
||
| efun |
|
||
|
yeah they are LED's
oh okay.. so there's no wires or anything connecting it to the car? lol.. i dont get it.. sorry.. hmm
_________________ Holden = Hope Our Luck Doesn't End Now |
||
| Top | |
||
| frd906n |
|
||
|
dont u have to wire the leds in, becuase i dont think the normal globes will work in them
_________________ Daily Driver, Series 1 Au Forte Quote: Posted by Xcabbi, Does it slap or rattle? Rattle is more to do with timing chains and tensioners. Slap is more to do with lifters, rings, bearings or GENIII boat anchors
|
||
| Top | |
||
| phil545 |
|
|||
|
they are the exact same ones i got mate!! i seen so many of that design but with the normal tail lights (not LED). Your lucky your in NT, ill let that one slide, i haven't seen any falcons with these in Sydney yet
they are easy as to install, its all the same wiring, just plug and play, but there is a little plastic clip that sits in the corner (bottom right of pic below) of the rear quarter panel, you have to sort of wedge a screw driver gently in there as you pull them out, if you break it (which mine did) they are $7.50 from ford which a rip as the part prolly cost 2 cents from China. You will see the metal pin on the tail light that goes into this clip to see what i am talking about.
_________________ I hate arriving at my destination as then I have to get out of my car! |
|||
| Top | |
|||
| efun |
|
||
|
ohh awesome that makes more sense.. so this clip.. it's basically there to hold the tail light in place? hah and i need to wedge it with a screw driver to release it? .. hah
_________________ Holden = Hope Our Luck Doesn't End Now |
||
| Top | |
||
| phil545 |
|
|||
|
yeah it holds the end of the tail light in against the car. the 2 screws obviously do most of the work but the clip holds the rounded part of the light against the car. Yeah you will need to use a small flat head screw driver and be gentle to wedge the light out of the clip.
Pic of them on my car here - ford-bodykits-f15/show-us-ur-modded-au-ba-bf-t38893-420.html
_________________ I hate arriving at my destination as then I have to get out of my car! |
|||
| Top | |
|||
| efun |
|
||
|
ohh awesome, yeah ive seen your pics before ahaha they look good, can't wait until i get em. havent seen any one here with them yet
 thanks for the tips and advice and all  really appreciate it!
_________________ Holden = Hope Our Luck Doesn't End Now |
||
| Top | |
||
| phil545 |
|
|||
|
No worries mate, yeah i havnt seen anyone either... well until you get them and post up
_________________ I hate arriving at my destination as then I have to get out of my car! |
|||
| Top | |
|||
| efun |
|
||
|
haha ill deff post the pics up, wont be a while until i get em thou, i really want the extractors and exhaust system first :p
_________________ Holden = Hope Our Luck Doesn't End Now |
||
| Top | |
||
| phil545 |
|
|||
|
Haahah yeah i went done the visual mods first and then moved onto performance, i went the full exhaust system as well, best thing ever, they respond really well
_________________ I hate arriving at my destination as then I have to get out of my car! |
|||
| Top | |
|||
| efun |
|
||
|
oh nice, do you have CAI or.. just stock induction still
_________________ Holden = Hope Our Luck Doesn't End Now |
||
| Top | |
||
| phil545 |
|
|||
|
Just stock induction atm. Once i have done the body kit, the CAI is next on the list so probably a months time i will be installing an ss inductions growler kit. You will find lots of people on here diss you for wasting your money on them as they are pricey but i say if you got the money may as well do it properly. People make their own or install the F6 secondary intake but meh i rather spend the money plus get the nice growl it makes
_________________ I hate arriving at my destination as then I have to get out of my car! |
|||
| Top | |
|||
| winman |
|
|||
|
i made a legal induction growl for 30 bucks, 25 on a cheap, but decent pod filter, then 5 bucks on flute board which i used to make a airbox, the airbox is a temporary design till i get something pre-designed and molded, but hey for 5 bucks it does the trick to keep hot air out of the pod, while making the car legal
_________________ BA XR6 |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 19 guests |
