|
| MRE-50L |
|
|||
|
hey ratman , is that vince's EL
_________________ Chance Favors The Prepared Mind ! |
|||
| Top | |
|||
| XH5LWEPN |
|
|||
|
Scaffy that is looking very sweet now. It should have looked like that the day it drove out of the w/shop.
_________________ STREETBUILT RACING |
|||
| Top | |
|||
| Scaffy |
|
|||
|
Thanks Jeff, it sure should have. I took a bit of time to clean it all up under there a while back and now whenever it gets opened, I give it a quick wipe down. I threw the fuel pressure guage in yesterday too which I think adds to the look.
_________________ Trickflow Street Heat top end kit, 70mm BBK TB & EGR, 24lb injectors, Underdrives & 3.73s: 275rwhp - 13.15@105mph NA / 12.37@116mph N20 |
|||
| Top | |
|||
| ratman |
|
|||
|
MRE-50L wrote: hey ratman , is that vince's EL
That it is my friend.
_________________ There's no replacement for XR8 displacement
|
|||
| Top | |
|||
| MRE-50L |
|
|||
|
man next time you see vince tell him dave (with grey EL ) from tempe tyres say HI ! and i want the 20" AME's
 ( cause i know they fit my car  )
_________________ Chance Favors The Prepared Mind ! |
|||
| Top | |
|||
| ratman |
|
|||
|
MRE-50L wrote: man next time you see vince tell him dave (with grey EL ) from tempe tyres say HI ! and i want the 20" AME's
( cause i know they fit my car )No worries, will do tomorrow as I'll be detailing my car all arvo/night. at his shop. After all the wheel changes, its fitting he nows sells rims and tyres from the shop too. Personally, the 20s fit but even with the pumped guards and ryobi modified springs, the car just didn't sit right, 19s still look the best.
_________________ There's no replacement for XR8 displacement
|
|||
| Top | |
|||
| edfairmont4.0 |
|
|||
|
lol there would T500 peices of broken gearbox under the car, 500 broken peices...................
_________________ ED Fairmont, Ghia mock DOHC-T 11.6 @ 118 Trying to get back to the 1/4! |
|||
| Top | |
|||
| LTDHO |
|
|||
|
This is the old egine bay of the LTD before I wentr for a bigger cooler and powder coated the upper inlet manifold.
Here is old pic of the XR. I have since removed the cover and fitted thermo's. 
|
|||
| Top | |
|||
| falcon gl |
|
||
|
i remember seeing that ltd in the ford mag, you also had a 6 speed behind that didnt you, how much did everything cost u all up
|
||
| Top | |
||
| green car |
|
||
|
Very nice scaffy.
_________________ 165 Killer Wasps all packaged in a green kmart car, almost an explorer in a way... |
||
| Top | |
||
| Stevo |
|
|||
|
XH5LWEPN wrote: Barnacus, is that an AU 5.0 alternator?
Heres mine.  Hey XH5LWEPN, is that the stock distributor with a MSD cap? Or a new MSD Distributor? How much that set you back? |
|||
| Top | |
|||
| Stevo |
|
|||
|
nevermind just read in another thread its the cap and you got it from A1 Hi Performance
|
|||
| Top | |
|||
| BOTTLEDUP |
|
|||
|
green car wrote: Very nice scaffy.
Post a pic of ur killa engine combo Shannon!! Hahaha.
_________________ TE50 T1 P01 |
|||
| Top | |
|||
| green car |
|
||
|
It's a nasty piece of work my windsor haha.I might just try and put up a pic
_________________ 165 Killer Wasps all packaged in a green kmart car, almost an explorer in a way... |
||
| Top | |
||
| 3x-puursui7 |
|
||
|
haha this is all i've done and its not even special just off the shelf, but will soon be getting alot sexier with lots of new bits
_________________ mmmmmmmmmmm 220 manual goodness! Last edited by 3x-puursui7 on Thu May 15, 2008 12:47 am, edited 1 time in total. |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 24 guests |
