|
| gunit18 |
|
||
|
hi, now has come the time to fit the Pro M maf & 24's...
i dummy fitted the maf today & the only way i figure it'll fit is with a custom airbox or shielding. Id have to remove the stock airbox. this is because the maf has a huge 6'' K & N pod fitted to it. took the pod off and the maf certainly didnt fit to the airbox where the s**t maf is now. can i apply like the BA XR8's do with the shielded pod? wat sort of material could i use or is there a company that could fit this up for me? the maf is a 77mm unit. any ideas peoplesor opinions? thanks |
||
| Top | |
||
| AXR88U |
|
|||
|
I cut my EF one to fit an 80mm vortech no worries (for rego purposes),
should be able to enlarge the hole enough to fit the end of a pro-M in.
_________________ ________________________________________
|
|||
| Top | |
|||
| gunit18 |
|
||
|
did u have the pod in the airbox or just screw the maf to the airbox like stock, using a panel filter?
|
||
| Top | |
||
| greg302 |
|
||
|
sorry to go off topic where did you get your pro m from gunit and how much you pay
_________________ 347, crane cam, Pro topline 180 heads, Edelbrock victor efi intake, 80mm C&L maf, 75mm tb, 30lb injectors and 1/4 horse |
||
| Top | |
||
| AXR88U |
|
|||
|
{USERNAME} wrote: did u have the pod in the airbox or just screw the maf to the airbox like stock, using a panel filter?
just like stock
_________________ ________________________________________
|
|||
| Top | |
|||
| gunit18 |
|
||
|
got the injectors and pro m off coral for around $350 shipped.
so u reakon just make the original hole in the airbox larger to accomodate the larger MAF? might have a go, it'll save dramas of buying or making a new box... did u have anything inbetween the maf and airbox, like a rubber gasket of some sort AXR88U? |
||
| Top | |
||
| XR9UTE |
|
||
|
Make your own box to seal the Pro-M filter from engine heat. That MAF works best when used with it's original filter.
Pete. |
||
| Top | |
||
| kato |
|
||
|
I had a mate who's a boilermaker make up a flange identical to the factory one and got it welded to my maf, worked well.
_________________ EF XR8 5spd: 302ci /178rwkw |
||
| Top | |
||
| AXR88U |
|
|||
|
{USERNAME} wrote: got the injectors and pro m off coral for around $350 shipped.
so u reakon just make the original hole in the airbox larger to accomodate the larger MAF? might have a go, it'll save dramas of buying or making a new box... did u have anything inbetween the maf and airbox, like a rubber gasket of some sort AXR88U? My maf is a flangless one to suit a pod. Just made to hole very neat & had a tight fit. When the hole size is close, try the maf up against it and take little bits at a time out of the lid. I was'nt that fuss about sealing it up with anything as it is a really good fit. I used one of those little die grinders to do it.
_________________ ________________________________________
|
|||
| Top | |
|||
| gunit18 |
|
||
|
Quote: My maf is a flangless one to suit a pod. Just made to hole very neat & had a tight fit. When the hole size is close, try the maf up against it and take little bits at a time out of the lid.
I was'nt that fuss about sealing it up with anything as it is a really good fit. ok, i'll have a go at this and seal the pod in the airbox. see how i go. mite get my mate to fit the injectors and then get it on the dyno to tune the unichip. and there's no real difference as im using the 94-95 pro m maf and injectors yes? cheers guys |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 30 guests |
