|
| MARK.TANIA |
|
||
|
wash it with deasel and get it rebuilded sorry about the milky motor mate
|
||
| Top | |
||
| blackjack_original |
|
||
Posts: 3516 Joined: 8th Nov 2004 |
[self-deleted]
Last edited by blackjack_original on Fri Jun 06, 2014 10:07 pm, edited 1 time in total. |
||
| Top | |
||
| 4.9 EF Futura |
|
|||
|
{USERNAME} wrote: Holy f**k. As bad as it is, thats kinda cool.
Do i have your permission to post that on other forums? Haha, mate those pics are enough to put someone off their dinner. Alas, poor windsor. I knew him well.
_________________ I promise..... I will never die. |
|||
| Top | |
|||
| XHII V8S |
|
||
|
hmm hydrochloric acid bath maybe?
_________________ Pacies & single 2.5'. New manifold to come soon... |
||
| Top | |
||
| mrnasty |
|
|||
|
new motor?
_________________ Cougar Zero makes my pants fit nice. |
|||
| Top | |
|||
| CLEANEB |
|
|||
|
i dunno about you guys...but that looks kinda yummy!
|
|||
| Top | |
|||
| Hyena |
|
|||
|
JEEEEESUS!
As said the bearings will be rooted so I'd go for a full rebuild while it's in pieces. You'd think an acid bath would sort it out but if you have access to a gurney I'd try that first to remove the bulk of it. {USERNAME} wrote: Coolant was just changed... Full Ford Service, so hopefully they put the genuine stuff in. Paid enough for it!!
I think that's the least of your worries now!!
_________________
|
|||
| Top | |
|||
| ef302 |
|
|||
|
{USERNAME} wrote: Holy f**k. As bad as it is, thats kinda cool.
Do i have your permission to post that on other forums? Go for your life. At least my misfortune can entertain the masses!! 
High pressure wash doesn't work. Firstly it has to wash somewhere and I can't imagine the EPA approving of that mix going down a drain. Secondly, it doesn't come off!! The sump should theoretically be the easiest to clean, due to a lack of moving parts or obstructions, but while scooping out the worst of it was possible, the remainder just didn't budge. It simply flaked off in small quantities and made a mess! Boiling water just sat there, petrol doesn't penetrate and even the guy who cleans the workshop floor had a crack! He brewed up some nastiness that SHOULD shift anything, but it didn't penetrate in the slightest!
_________________ Have YOU driven a monster truck lately?? |
|||
| Top | |
|||
| Disturbed_Dave |
|
|||
|
easy fix.... BF XR6T engine
sorry to see the mess.... couldnt have happened to a better make of car
_________________
|
|||
| Top | |
|||
| xr8ute |
|
||
|
{USERNAME} wrote: new motor?
Bingo! |
||
| Top | |
||
| Pulco |
|
||
|
its electrolysis all right.... the problemwas most prob caused by not havin a good enuff earth from the block to the chassis!
its a problem in the i6 as well...especially on the exuast side of the head!
_________________
|
||
| Top | |
||
| EBXR8380 |
|
|||
|
Na just check crank journal, rods for wear and roundness..Chances are bore will be fine.. Just new rings and bearings,new timing chain and front timing cover...Thats after a good wash or hot tank....In that case new cam bearings too....
_________________ As in ZOOM 126 edition |
|||
| Top | |
|||
| Walker |
|
|||
|
Machinists usually grease up an old cam and throw it in to save the cam bearings during a hot tank.
I'd definately freshen the motor up though. |
|||
| Top | |
|||
| Gaz |
|
||
|
blowtorch?
thats seriously nasty. soak it in petrol and throw a match? maybe itll burn off :p
_________________ 2007 Steel BF Ghia MKII V8 - 19" GTP's + Superlows |
||
| Top | |
||
| sasr |
|
||
|
lol, that sucks man.
If you give me some chemicals involved I could do some reactions to see what the hell the mf of that stuff is!
_________________ The bee's are on the what now? |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 0 guests |
