
| 
 | 
| mspw | 
 | |||
| 
 | 
							
							As the title suggests. 
 Has anyone been in a position to examine both. In your opinion, what would be required to fit, say the BA XR twin-piston sets onto an EF? Are we ultimately adding or subtracting material from the callipre? Regards 
 _________________ 
 | |||
| Top |  | |||
| scotts840 | 
 | ||
| 
 | 
							
							well yes. it can be done, but it would probably be just as cheap to sell the ef/l and buy a ba. . . . .
 or the cheaper option is to get an aftermarket upgrade kit. then you can have 4 pot callipers | ||
| Top |  | ||
| Interceptor | 
 | ||
| 
 | 
							
							remember, what seems mpossible only requires appropriate amounts of time and money to achieve success						
						
						
								
							 
 _________________ Banned | ||
| Top |  | ||
| JOSE | 
 | |||
| 
 | 
							
							cmon, it cant be that hard, if someone wants to give me a pair of calipers rotors and pads, i recon i could make em fit						
						
						
								
							 
 _________________ Because i can. | |||
| Top |  | |||
| xr8 dismantler | 
 | |||
| 
 | 
							
							Nick and myself have looked into this in the last week,
 may have a answer soon   | |||
| Top |  | |||
| xpression | 
 | |||
| 
 | 
							
							well... u might be able to fit like an AUII stub? or a BA stub and wheel bearing setup to your ef? and bolt the callipers etc to that?
 im not sure but its a thouht just the same | |||
| Top |  | |||
| Nicko | 
 | |||
| 
 | 
							
							its a bit harder than that, as you haev to worry about offset etc.
 but it is being investigated and hoepfully we may have a solution very soon Au2 brakes and ba are different but you would see a huge performance increase from putting on the au2 stuff but the fact is it isnt something you can do a straight swap over on 
 _________________ Nicko | |||
| Top |  | |||
| fairmont1998 | 
 | |||
| 
 | 
							
							Going by what I've read it's a big job.
 You'll need AU/BA uprights, and they won't suit EF upper and lower arms. May end up needing K frame and arms from an AU/BA. But I haven't tried and may be wrong! 
 _________________ 2008 WQ Fiesta XR4 | |||
| Top |  | |||
| Nicko | 
 | |||
| 
 | 
							
							not if we have anything to do with it!						
						
						
								
							 
 _________________ Nicko | |||
| Top |  | |||
| xr8 dismantler | 
 | |||
| 
 | 
							
							SHHHHH   dont tell Nick
 "i will never tell  " | |||
| Top |  | |||
| Nicko | 
 | |||
| 
 | 
							
							no i only promised not to tell about your plan to take over the world						
						
						
								
							 
 _________________ Nicko | |||
| Top |  | |||
| fairmont1998 | 
 | |||
| 
 | {USERNAME} wrote: not if we have anything to do with it! That's the right attitude, get in and try.   
 _________________ 2008 WQ Fiesta XR4 | |||
| Top |  | |||
| Who is online | 
|---|
| Users browsing this forum: No registered users and 40 guests |