|
| a1drake |
|
|||
|
{USERNAME} wrote: did anyone else notice that the rubber on the bonnet is now in the way a bit and hits the snorkel? its making my bonnet sit up a bit on the passenger side, i will be triming the rubber from there when i get home, but just wondering did anyone else have a better solution? g day i had no probs with bonnet. i did have to play with the rubbers to stop losing air thru any gaps beteewn rubber & bonnet 
_________________ eb 4.0 falcon & f150 351 & caprice 5.0 |
|||
| Top | |
|||
| a1drake |
|
|||
|
This modification costs a total of $42.00 (New Genuine Snorkel), and takes approximately 10 / 15 Minutes to fit
The Ford Part Number for the Snorkel is EHC9C675-A.this is for xh /eb ed snorkel exchange 
_________________ eb 4.0 falcon & f150 351 & caprice 5.0 |
|||
| Top | |
|||
| twirqurky |
|
||
|
{USERNAME} wrote:
FernTree Gully Auto Salvage (site sponsor) sell these for $42 including psotage. If you have an EF or an EL thats the one you want. if your interested, check the FOr Sale thread. |
||
| Top | |
||
| a1drake |
|
|||
|
this mod with the bigger xh snorkel i have being very impressed ,it has helped with fuel usage seems to rev harder & quicker, also very smooth and effortless performance,i think i have picked up rwkw not many maybe 5/9 rwkw also i
 had disconnected battery to reset ecu , the eb took a while to adjust to this mod , but now all apples . u can really feel the intake sucking seems to like lots of air flow to it to wrap up this mod i ll give it a 10/10 
_________________ eb 4.0 falcon & f150 351 & caprice 5.0 |
|||
| Top | |
|||
| nannas_ed |
|
|||
|
{USERNAME} wrote: did anyone else notice that the rubber on the bonnet is now in the way a bit and hits the snorkel? its making my bonnet sit up a bit on the passenger side, i will be triming the rubber from there when i get home, but just wondering did anyone else have a better solution?
if your talking about the rubber seal doodaa the justy take it off thats what i done. i found that it was blocking the entire 'mouth' of the intake
_________________
|
|||
| Top | |
|||
| a1drake |
|
|||
|
{USERNAME} wrote: {USERNAME} wrote: did anyone else notice that the rubber on the bonnet is now in the way a bit and hits the snorkel? its making my bonnet sit up a bit on the passenger side, i will be triming the rubber from there when i get home, but just wondering did anyone else have a better solution? if your talking about the rubber seal doodaa the justy take it off thats what i done. i found that it was blocking the entire 'mouth' of the intake now that you say something about it and i found that the grill looks wrong bent up a bit on the bottom ,not sitting flat . and as goes the rubber. my rubber starts and stops  where it fits as if it was made 4 it from factory
_________________ eb 4.0 falcon & f150 351 & caprice 5.0 |
|||
| Top | |
|||
| noabs |
|
||
|
thanks twirqurky, I will contact them.
|
||
| Top | |
||
| a1drake |
|
|||
|
well i went down to dyno day 4, to test the cold air intake, so stripped all the mods which where easy to remove
 so i had basic stock car except exhust system.i picked up about 6 rwkw funny i thought that ,even when they opened up the air box to improve air flow bypassings my xh snorkel the rwkw dropped about 5 rwkw where everybody else increased about 6 rwkw ,so my finding is that the way i set it up is spot on.now time for the next mod .
_________________ eb 4.0 falcon & f150 351 & caprice 5.0 |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 115 guests |
