|
| madeaspack |
|
||
|
whats the best way to go about the ignition system wiring?
can it be done with the tfi? or do i need to change to a carby xf dizzy with an ignitor? or is it better to use a coil pack?its an au engine that stll has the crank sensor inplace cheers
_________________ 97 el xr6,5 speed short shifter,sequential scoop,no arial,freshly resprayed,low on 17's,3 inch zorst,stainless hi flo cat,snort stage 3 stainless manifold,garrett t04e,front mount cooler,wolf 3d ecu,seimens 760cc injectors,walbro fuel pump |
||
| Top | |
||
| 66 coupe |
|
||
|
you can use the TFI to provide the trigger pulse, but you will need to run a seperate coil ignitor.
You will also need to modify the distributor, and move the chopper wheel to provide the correct reference point, from memory it was around 60* before tdc. Much easier to use the CAS if its an AU engine |
||
| Top | |
||
| madeaspack |
|
||
|
do you know if the carby xf dizzys chopper wheel is already set at 60 degrees?
_________________ 97 el xr6,5 speed short shifter,sequential scoop,no arial,freshly resprayed,low on 17's,3 inch zorst,stainless hi flo cat,snort stage 3 stainless manifold,garrett t04e,front mount cooler,wolf 3d ecu,seimens 760cc injectors,walbro fuel pump |
||
| Top | |
||
| 66 coupe |
|
||
|
no, they need to be modified to work with a wolf - its a bit of messing around to get it right.
|
||
| Top | |
||
| madeaspack |
|
||
|
cool,si if i use the tfi for the output and then an ignitor to the coil with the chopper wheel set right it should be all good?
_________________ 97 el xr6,5 speed short shifter,sequential scoop,no arial,freshly resprayed,low on 17's,3 inch zorst,stainless hi flo cat,snort stage 3 stainless manifold,garrett t04e,front mount cooler,wolf 3d ecu,seimens 760cc injectors,walbro fuel pump |
||
| Top | |
||
| TURBO_GHIA |
|
|||
|
it was alot of f**k around to get it to work when i did it .id use the coilpacks or get an ems8860
_________________ HMMMM BOOST !!!
|
|||
| Top | |
|||
| TURBO_GHIA |
|
|||
|
i used an M&W ignitor. i had to modifiy the dizzy ,i took off the TFI modual and replace it with a part of an EA or XF dizzy i think it was it plugs into the part where the TFI plugs into but theres no tfi there its just a plug with 3 wires coming out of it .i then had to move the hall effect sensor inside .i cant remember it all as my mech did most of it .and then you have to set that at the right degrees and then set the base ,so when you setup the wolf you can get the most amount of advance
_________________ HMMMM BOOST !!!
|
|||
| Top | |
|||
| madeaspack |
|
||
|
thanks for your help and advice guys,i used an ignitor.modifying the dizzy was easy as i took out the hall effect sensor and elongated the holes so its fully adjustable now,like points kinda,measured 30 degrees of dizzy rotation and set it there,it was a few degrees out but the wolf can go to 90degrees,mines at about 70degrees of crank rotation btdc
_________________ 97 el xr6,5 speed short shifter,sequential scoop,no arial,freshly resprayed,low on 17's,3 inch zorst,stainless hi flo cat,snort stage 3 stainless manifold,garrett t04e,front mount cooler,wolf 3d ecu,seimens 760cc injectors,walbro fuel pump |
||
| Top | |
||
| madeaspack |
|
||
|
whats the purpose of the step up resistor?
_________________ 97 el xr6,5 speed short shifter,sequential scoop,no arial,freshly resprayed,low on 17's,3 inch zorst,stainless hi flo cat,snort stage 3 stainless manifold,garrett t04e,front mount cooler,wolf 3d ecu,seimens 760cc injectors,walbro fuel pump |
||
| Top | |
||
| TURBO_GHIA |
|
|||
|
to let the wolf reconise it i think
_________________ HMMMM BOOST !!!
|
|||
| Top | |
|||
| madeaspack |
|
||
|
thats what i assumed,i didnt use one,i had a good signal without it
_________________ 97 el xr6,5 speed short shifter,sequential scoop,no arial,freshly resprayed,low on 17's,3 inch zorst,stainless hi flo cat,snort stage 3 stainless manifold,garrett t04e,front mount cooler,wolf 3d ecu,seimens 760cc injectors,walbro fuel pump |
||
| Top | |
||
| TURBO_GHIA |
|
|||
|
when u hook it up look on the wolf program or hand controller and it will say error count make sure its not comming up with any
_________________ HMMMM BOOST !!!
|
|||
| Top | |
|||
| madeaspack |
|
||
|
i dont think it does,does it matter if it does?
_________________ 97 el xr6,5 speed short shifter,sequential scoop,no arial,freshly resprayed,low on 17's,3 inch zorst,stainless hi flo cat,snort stage 3 stainless manifold,garrett t04e,front mount cooler,wolf 3d ecu,seimens 760cc injectors,walbro fuel pump |
||
| Top | |
||
| TURBO_GHIA |
|
|||
|
it should be a CLEAN signal ,mines comes up with it sometimes but if it runs fine i wouldnt worry about it
_________________ HMMMM BOOST !!!
|
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 29 guests |
