|
| dave393 |
|
||
Age: 62 Posts: 17 Joined: 22nd Jul 2012 Ride: Dl ltd,Xe ghia,Xr5 turbo Location: Melbourne |
Hi guys my sons got an au series1 ute which he lent to a mate to move a fridge his clever mate has lost the ignition key and remote pad any ideas how I can start it and get it out of his driveway? Thanks dave.
|
||
| Top | |
||
| Papa Smurf |
|
||
|
dave393 wrote: Hi guys my sons got an au series1 ute which he lent to a mate to move a fridge his clever mate has lost the ignition key and remote pad any ideas how I can start it and get it out of his driveway? Thanks dave. If it still has the original Barrel and Key in it, take the VIN, starts with 6FPAAA JGCM, and get to your local Ford dealer, they should have the key number on record then, go to a locksmith with the number and have them cut your key. I think you may have to have it programmed to your car?. As to your remote, Ford has made them obsolete but you can still buy on Ebay http://www.ebay.com.au/itm/Keyless-Entr ... 19d882cfa9. |
||
| Top | |
||
| dave393 |
|
||
Age: 62 Posts: 17 Joined: 22nd Jul 2012 Ride: Dl ltd,Xe ghia,Xr5 turbo Location: Melbourne |
Thanks papa smurf the car does not have the original ignition barrel or key nor does he have the original remote pad so I can't even reprogramme a new remote pad any other ideas.thanks dave
|
||
| Top | |
||
| Papa Smurf |
|
||
|
This has the Chip key? You don't need another remote to add one to your vehicle.
You should be able to get a mobile Locksmith to come and figure out a key for you, not sure how much but I doubt it would be too much. |
||
| Top | |
||
| EF_wanabe |
|
||
|
Does the same key to start the car open up the door?
If so remove the door lock from the door take to lock smith and they will make you a key from the pin order that you gave them from your door lock |
||
| Top | |
||
| Papa Smurf |
|
||
|
That will only work if the key isn't a chip key.
|
||
| Top | |
||
| dave393 |
|
||
Age: 62 Posts: 17 Joined: 22nd Jul 2012 Ride: Dl ltd,Xe ghia,Xr5 turbo Location: Melbourne |
hi guys its not a chip key its the same key as an ef or el i can probably source an ignition barrel and key etc but how can i reprogramme a new key pad when i dont have the old one from what i can gather you need the key pad for that car so u can reprogramme a new one. any help would be very appreciated
|
||
| Top | |
||
| TROYMAN |
|
||
|
its easy to train the key pad.. you dont need the old ones..
you turn your ignition to acc and press the rear denist buttons 3 times within 5 seconds, the door locks will cycle you then press a button on the new key pads, the door locks will cycle again and your done... |
||
| Top | |
||
| snap0964 |
|
|||
|
Papa Smurf wrote: If it still has the original Barrel and Key in it, take the VIN, starts with 6FPAAA JGCM, and get to your local Ford dealer, they should have the key number on record Not always - My XR6 wagon was original in all respects, but they had no key nos.EF_wanabe wrote: Does the same key to start the car open up the door? They just need a lock cylinder - the locksmith I had did mine in minutes.If so remove the door lock from the door take to lock smith and they will make you a key from the pin order that you gave them from your door lock Mind you, bring some ID or whatever - I can't remember, but I may have shown rego papers, for what they were worth.
_________________ 96 XH Longreach 'S': LPG, Alarm, 3.23:1 LSD, Cruise, Trip Comp, ABS, Power Windows, Mid Series Dome Lt, Climate Ctrl |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 9 guests |
