|
| naughtyfalcon |
|
|||
|
we have an el wagon with no cruise control , i have installed the steering wheel controls , what i want to know is , does the control box behind the fuse panel need to be replaced with one from a vehicle fitted with cruise or will it connect up with the wiring from a cruise fitted vehicle, i will be sourcing the right harness from a wreckers.
i know i need the switch for the master cylinder and the module and cable , anything else i need ?
_________________
|
|||
| Top | |
|||
| 96ELGli |
|
||
|
Hello,
Have you read the Tech. Doc. ? If you car has ABS it has the high end harness with the Cruise connection already fitted. I read through it ages ago, and I think there is also a jumper you need to fit above where the clutch peddle would be or a switch if you have a manual.
_________________ Regards 96ELGli Last edited by 96ELGli on Sun Jun 01, 2014 10:27 am, edited 1 time in total. |
||
| Top | |
||
| naughtyfalcon |
|
|||
|
no abs and it's auto
_________________
|
|||
| Top | |
|||
| 96ELGli |
|
||
|
Hello,
You still may have to fit the jumper for it to work. The manual has a switch to turn the Cruise off when you put the clutch in, if Cruise is fitted you will need the jumper as an Auto wont have it put in at the factory if it isn't needed. I was going to fit Cruise to mine, which is why I read the Doc to see what I would have to do.
_________________ Regards 96ELGli |
||
| Top | |
||
| magna |
|
|||
|
if you're getting the factory wiring loom off a Futura/Fairmont you will need the entire loom that runs behind the dash to each airbag, all the way to the front drivers side ABS sensor.
otherwise just cut the loom where it goes into the cabin behind the brake booster, unpick just the wires that connect to the cruise plug and master cylinder switch and add about 30cms of wire to each of the 7 or so wires. then wire it up according to: ford-interior-f14/installing-cruise-control-on-non-abs-vehicle-t23377.html you won't require the jumper link either this way. |
|||
| Top | |
|||
| naughtyfalcon |
|
|||
|
can i use the wiring from another gli that has cruise fitted ?
_________________
|
|||
| Top | |
|||
| Barnzey |
|
||
|
you will have to replace the Dash loom and the firewall loom with looms from a vechile that has cruise control....... and then get the cruise control module that sits next to the brake booster.....
Yes big job.....
_________________ Fordz Rule |
||
| Top | |
||
| naughtyfalcon |
|
|||
|
yeah , no real biggy , just time to do it
_________________
|
|||
| Top | |
|||
| blueblood |
|
|||
|
A mate of mine was going to do this, he eventually decided aftermarket was a lot less stuffing around. Works well, not too expensive and tidy install.
_________________ 93 EB S-XR8 5 SPEED, |
|||
| Top | |
|||
| StevenBruzz |
|
|||
|
i fitted it to mine didnt need to put the jumper in n its up on the brake switch loom i have everything but the switches for sale if your keen i think i put a add in the buy section but not sure if it went up net keept dropping out
|
|||
| Top | |
|||
| naughtyfalcon |
|
|||
|
how much you looking for with postage to 2371 , we already have switches in
_________________
|
|||
| Top | |
|||
| StevenBruzz |
|
|||
|
Pm you
|
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 3 guests |
