Fordmods Logo

Imobiliser on 

 

Page 1 of 1 [ 11 posts ] 

 
 Post subject: Imobiliser on
Posted: Fri Feb 16, 2018 7:50 pm 
Fordmods Newbie
Offline

Age: 60

Posts: 5

Joined: 16th Feb 2018

Ride: 2007 Bf Ford

Location: Sawyers Valley,Perth
WA, Australia

2007 bf ute Have replaced wiring harness(after falling apart) on the back of my ignition barrel and now has immobilizer light flashing and wont start,have tried to reprogram key but no luck.. also has code display on ICC unit?
Top
 Profile  
 
 
 Post subject: Re: Imobiliser on
Posted: Sat Feb 17, 2018 10:40 am 
Getting Side Ways
Offline
User avatar

Age: 41

Posts: 402

Joined: 24th Jun 2014

Gallery: 4 images

Ride: BA XR6 Turbo

Location: Jamestown
SA, Australia

Rsc Kiwi wrote:
2007 bf ute Have replaced wiring harness(after falling apart) on the back of my ignition barrel and now has immobilizer light flashing and wont start,have tried to reprogram key but no luck.. also has code display on ICC unit?



Was it the wiring harness you replaced or did you install a new/used column. How did you try to reprogram the key? The keys on the AU S2 cannot be programmed my leaving the ignition on like in the old E series reprogramming keys generally requires a trip to ford or a decent auto elect with the right scan tool.

IF you have put in a new/second hand column you SHOULD be able to use your key cylinder out of your original column in the new column to get you going again.

To remove key cylinders (check on your old one first) there should be a brass pin in the side of the column on the key side its only about 3mm round (its in a bugger of a spot to get to and see on the car) if you find and see that switch your key to acc press the little pin in you may need to "jiggle" the key and cylinder around a little and it should slip out installation is the same process. DO NOT SWITCH BACK OR LET YOUR COLUMN SWITCH BACK TO FROM ACC TO LOCK YOU WILL RUIN THE COLUMN as it will shoot the locking pin into the column permanently disabling it

Hope this is of some help

 

_________________

Current Ride
BA XR6 Turbo, P3 Paint, BP Trim, Fully Stock Mods to Come!
BA XR6 , P3 Paint, BG Trim, !
1995 EF XR6 The newest member of my ford family!

BLUE BLOOD
Previous Rides
RIP 1996 EF Falcon furura, White sacrificed for parts
1997 EL Falcon
1980 Ford Escort

Top
 Profile  
 
 
 Post subject: Re: Imobiliser on
Posted: Sat Feb 17, 2018 12:57 pm 
Fordmods Newbie
Offline

Age: 60

Posts: 5

Joined: 16th Feb 2018

Ride: 2007 Bf Ford

Location: Sawyers Valley,Perth
WA, Australia

just wiring harness replaced. Disconnected battery while i worked on it. Removed steering column so as i could work on harness. not sure if ICC code would have anything to do with it not starting. Have put the original key and barrel back in?
Top
 Profile  
 
 
 Post subject: Re: Imobiliser on
Posted: Sat Feb 17, 2018 1:14 pm 
Moderator
Offline
User avatar

Age: 46

Posts: 2484

Joined: 6th Oct 2005

Ride: 93EB Fairmont / BA Falcon XR6T

Location: Western Sydney
NSW, Australia

The ICC does not require a code on the BA.
It should dissappear once the car starts.

 

_________________

93 EB II Fairmon8 with 17' EL GT's / Clear indicators / H.I.Ds / Sports exhaust / Lowered 2' / K&N / XR6 ECU.
2004 BA MKI XR6T in Lightning Strike paint / K&N / XR8 bonnet / BF lights and a few tweaks.

Top
 Profile  
 
 
 Post subject: Re: Imobiliser on
Posted: Sun Feb 18, 2018 8:07 am 
Fordmods Junkie
Offline
User avatar

Posts: 3925

Joined: 22nd Jan 2009

Ride: '03 BA & '06 BF Wagooons

Location: Geeelong
VIC, Australia

93EB wrote:
The ICC does not require a code on the BA.
It should dissappear once the car starts.



the BA i have shows needs code, however after startup it's fine.
Top
 Profile  
 
 
 Post subject: Re: Imobiliser on
Posted: Sun Feb 18, 2018 10:23 am 
Getting Side Ways
Offline
User avatar

Age: 41

Posts: 402

Joined: 24th Jun 2014

Gallery: 4 images

Ride: BA XR6 Turbo

Location: Jamestown
SA, Australia

Mad2 wrote:
93EB wrote:
The ICC does not require a code on the BA.
It should dissappear once the car starts.



the BA i have shows needs code, however after startup it's fine.



Quiet common for it to read code for a few seconds after a battery disconnect switching to ignition usually solves the issue the "code" in these is sent and received


Rsc Kiwi wrote:
just wiring harness replaced. Disconnected battery while i worked on it. Removed steering column so as i could work on harness. not sure if ICC code would have anything to do with it not starting. Have put the original key and barrel back in?
over the CAN bus so is always stored in the BCM unless you change the ICC

Sounds like its not reading the key to disable the security. Everything been hooked back in the column and under the dash? the little green plug is plugged into the reader around the key cylinder? all the lights coming on the dash when you switch to ignition?

 

_________________

Current Ride
BA XR6 Turbo, P3 Paint, BP Trim, Fully Stock Mods to Come!
BA XR6 , P3 Paint, BG Trim, !
1995 EF XR6 The newest member of my ford family!

BLUE BLOOD
Previous Rides
RIP 1996 EF Falcon furura, White sacrificed for parts
1997 EL Falcon
1980 Ford Escort

Top
 Profile  
 
 
 Post subject: Re: Imobiliser on
Posted: Sun Feb 18, 2018 11:04 am 
Fordmods Newbie
Offline

Age: 60

Posts: 5

Joined: 16th Feb 2018

Ride: 2007 Bf Ford

Location: Sawyers Valley,Perth
WA, Australia

Only imobiliser light comes on when key inserted?
Top
 Profile  
 
 
 Post subject: Re: Imobiliser on
Posted: Sun Feb 18, 2018 12:55 pm 
Getting Side Ways
Offline
User avatar

Age: 41

Posts: 402

Joined: 24th Jun 2014

Gallery: 4 images

Ride: BA XR6 Turbo

Location: Jamestown
SA, Australia

all fuses intact? Almost sounds like there is something wrong in the ignition switch and the loom you have fixed.

seems to me its not making contact where it should in the switch.

EDIT check your ignition fusable link under the bonnet in the box there

 

_________________

Current Ride
BA XR6 Turbo, P3 Paint, BP Trim, Fully Stock Mods to Come!
BA XR6 , P3 Paint, BG Trim, !
1995 EF XR6 The newest member of my ford family!

BLUE BLOOD
Previous Rides
RIP 1996 EF Falcon furura, White sacrificed for parts
1997 EL Falcon
1980 Ford Escort

Top
 Profile  
 
 
 Post subject: Re: Imobiliser on
Posted: Sun Feb 18, 2018 6:19 pm 
Fordmods Newbie
Offline

Age: 60

Posts: 5

Joined: 16th Feb 2018

Ride: 2007 Bf Ford

Location: Sawyers Valley,Perth
WA, Australia

Big thanks.I replaced fuses under bonet and started first pop ...saved me $$$$
Top
 Profile  
 
 
 Post subject: Re: Imobiliser on
Posted: Sun Feb 18, 2018 6:19 pm 
Fordmods Newbie
Offline

Age: 60

Posts: 5

Joined: 16th Feb 2018

Ride: 2007 Bf Ford

Location: Sawyers Valley,Perth
WA, Australia

Big thanks.I replaced fuses under bonet and started first pop ...saved me $$$$
Top
 Profile  
 
 
 Post subject: Re: Imobiliser on
Posted: Sun Feb 18, 2018 6:45 pm 
Getting Side Ways
Offline
User avatar

Age: 41

Posts: 402

Joined: 24th Jun 2014

Gallery: 4 images

Ride: BA XR6 Turbo

Location: Jamestown
SA, Australia

No worries at all Glad its sorted

 

_________________

Current Ride
BA XR6 Turbo, P3 Paint, BP Trim, Fully Stock Mods to Come!
BA XR6 , P3 Paint, BG Trim, !
1995 EF XR6 The newest member of my ford family!

BLUE BLOOD
Previous Rides
RIP 1996 EF Falcon furura, White sacrificed for parts
1997 EL Falcon
1980 Ford Escort

Top
 Profile  
 
Display posts from previous:
Sort by  
 Page 1 of 1  [ 11 posts ] 

Who is online

Users browsing this forum: No registered users and 5 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

 

 

It is currently Fri Mar 29, 2024 1:08 pm All times are UTC + 11 hours

 

 

(c)2014 Total Web Solutions Australia - Australian Web Hosting and Domain Names