Fordmods Logo

troymans ea s pack build thread 

 

Page 3 of 10 [ 146 posts ] Go to page Previous  1, 2, 3, 4, 5, 6 ... 10  Next

 
Posted: Fri May 30, 2008 12:21 pm 
Getting Side Ways
Offline

Posts: 5503

Joined: 20th May 2005

Gallery: 11 images

Ride: EB1 Fairmont Ghia T5 Wagon

Location: Seven Hills, Sydney
NSW, Australia

TROYMAN wrote:
have rego coming up and im going to need some rear tyres aswell..


I wonder why that is..............

BenJ

 

_________________

BenJ's EB T5 DOHC Ghia Wagon - Current Ride
BenJ's EB GL Sedan - Previous Ride
My respect and thanks go to - snap0964, Paulmac, SWC and MRE-50L

Top
 Profile  
 
 
Posted: Fri May 30, 2008 12:34 pm 
Moderator
Offline

Posts: 14489

Joined: 7th Nov 2004

Ride: AU XR8

Location: a shit suburb in sydney
NSW, Australia

BenJ wrote:
TROYMAN wrote:
have rego coming up and im going to need some rear tyres aswell..


I wonder why that is..............

BenJ


ummm :roll: i dont know?
i think its got something to do with umm a new diff and a heavy foot lol...
Top
 Profile  
 
 
Posted: Fri May 30, 2008 12:38 pm 
Getting Side Ways
Offline

Posts: 6113

Joined: 8th May 2007

TROYMAN wrote:
thanks guys..
i dont know what to do next :?:
im running out of mods lol..


that car looks hot....... only thing i could possibly see for improvement is remove the badge from the bonnet and place it in the grille.

The 2 badge look for the front looks a bit funny, but other than that its a very sweet ride and a real credit to you
Top
 Profile  
 
 
Posted: Fri May 30, 2008 2:41 pm 
Moderator
Offline

Posts: 14489

Joined: 7th Nov 2004

Ride: AU XR8

Location: a shit suburb in sydney
NSW, Australia

FordFairmont wrote:
TROYMAN wrote:
thanks guys..
i dont know what to do next :?:
im running out of mods lol..


that car looks hot....... only thing i could possibly see for improvement is remove the badge from the bonnet and place it in the grille.

The 2 badge look for the front looks a bit funny, but other than that its a very sweet ride and a real credit to you


thanks mate..
yea i know the 2 badge look does look a bit funny..
its a set back of having a ea bonnet with a ed xr grill. if it ever gets a re-spray the badge recess will be filled in.
so at the moment its got a tickford badge in the grill instead of having 2 ford badges.....
Top
 Profile  
 
 
Posted: Sun Jun 01, 2008 9:50 am 
Getting Side Ways
Offline
User avatar

Posts: 649

Joined: 20th Mar 2005

Gallery: 2 images

Very impressive there Troyman. That is a wicked EA.

Its good to see all the mods over the years placed
in the one thread.
Top
 Profile  
 
 
Posted: Wed Jun 11, 2008 8:00 pm 
Moderator
Offline

Posts: 14489

Joined: 7th Nov 2004

Ride: AU XR8

Location: a shit suburb in sydney
NSW, Australia

ok
here is my latest mod in progress.
i aquired a pair of siera cosworth vents.
i gave them a few coats of undercoat and a light coat of gold to match the bonnet..
hopefully we will have some sun light tomorrow so i can finish the paint off..
then the scary part is having to cut the bonnet out to fit them :)

here are a few pics of then just sitting on the bonnet..

You do not have the required permissions to view the files attached to this post.
Top
 Profile  
 
 
Posted: Wed Jun 11, 2008 8:29 pm 
Getting Side Ways
Offline

Posts: 548

Joined: 28th Oct 2005

Ride: Peacock EB Falcon

Location: Brisbane
QLD, Australia

The vents will look great... but you really should store that bonnet and get an EB one cut and painted up.

Also wheres the ef/el fuel flap doco? :p

 

_________________

Wanted, CFI manifold

Top
 Profile  
 
 
Posted: Wed Jun 11, 2008 8:43 pm 
Getting Side Ways
Offline
User avatar

Age: 44

Posts: 907

Joined: 13th Jul 2005

Gallery: 10 images

Ride: ef futura/ef fairmont

Location: sydney
NSW, Australia

hey troy bring them in alittle and sit them on the crease line but apart from that very nice

 

_________________

custom airbox,custom intake
paccie comps,lukey 2.5 cat back,high flow cat
CMS stg2 head,CMS stg2.A. cam,CMS hybrid auto with mod shift,3.9 lsd
custom 3500rpm hi stall
ANZ mayhem 18's,custom interior,venom body kit,xr wing,jumbo 2' low springs
143rwkw and 407rwnm on CMS dyno

Top
 Profile  
 
 
Posted: Wed Jun 11, 2008 10:18 pm 
Moderator
Offline

Posts: 14489

Joined: 7th Nov 2004

Ride: AU XR8

Location: a shit suburb in sydney
NSW, Australia

knowsfords wrote:
wheres the ef/el fuel flap doco? :p


ok this is how to put metal ef door flap onto a ea/ed.this was done a few months back but i havnt fitted it as the paint i had didnt match..
to do this you must have the remote fuel door release..
first you need the plastic ea fuel flap to get the hinge from.
you can do this by prying the plastic near the hinge which pretty much breaks the plastic. see pic 1..
and you can then pull the hinge out.

then you need the ef fuel door and you need to open the rolled metal where the ef hinge pin sits with a screw driver to remove the hinge pin..
see pic 2..(i lost the original pic so i re used the after pic)

the ea hinge removed see pic 3

once the pin is removed you now can fit the body side of the hinge from the ea into the ef fuel door by pushing the lower side of the hinge into the lower part first and then push the top into the part that has been open with the screw driver
i had to fit a small washer to the top of the hinge to shim the door up for good alignment on the hinge and close the metal around the pin with long nose pliers.see pic 4..

once this is done you need to straighten out the latch a bit and you also need to re drill a hole for the remote release pin..see pic 5

there may be a bit of adjusting to get it to fit right and latch properly..
there are a few others that i know have done the same mod with slightly different methods but still got the same results..

You do not have the required permissions to view the files attached to this post.

Last edited by TROYMAN on Wed Jun 11, 2008 10:21 pm, edited 1 time in total.

Top
 Profile  
 
 
Posted: Wed Jun 11, 2008 10:20 pm 
Moderator
Offline

Posts: 14489

Joined: 7th Nov 2004

Ride: AU XR8

Location: a shit suburb in sydney
NSW, Australia

and finally fitted to the car..

i have removed it from the car untill i get a better paint match lol

You do not have the required permissions to view the files attached to this post.
Top
 Profile  
 
 
Posted: Thu Jun 12, 2008 12:02 am 
Getting Side Ways
Offline

Posts: 5503

Joined: 20th May 2005

Gallery: 11 images

Ride: EB1 Fairmont Ghia T5 Wagon

Location: Seven Hills, Sydney
NSW, Australia

Nice work Troyman.

The vents look great and will suit the car nicely.

And thanks for doing the doco on the fuel flap mod.

Save me from having to do it now, phew!

Cheers
BenJ

 

_________________

BenJ's EB T5 DOHC Ghia Wagon - Current Ride
BenJ's EB GL Sedan - Previous Ride
My respect and thanks go to - snap0964, Paulmac, SWC and MRE-50L

Top
 Profile  
 
 
Posted: Sun Jun 15, 2008 1:49 am 
Moderator
Offline

Posts: 14489

Joined: 7th Nov 2004

Ride: AU XR8

Location: a shit suburb in sydney
NSW, Australia

no probs..
Top
 Profile  
 
 
Posted: Sun Jun 15, 2008 2:12 am 
Moderator
Offline

Posts: 14489

Joined: 7th Nov 2004

Ride: AU XR8

Location: a shit suburb in sydney
NSW, Australia

ok i got busy this afternoon on the cosworth vents and made a template and measured and marked the spots to cut.
i only had enough time to cut one side lol.
so ive been driving around tonight with a square hole in my bonnet..

this is as far as i got..

You do not have the required permissions to view the files attached to this post.
Top
 Profile  
 
 
Posted: Sun Jun 15, 2008 2:15 am 
Getting Side Ways
Offline

Posts: 5503

Joined: 20th May 2005

Gallery: 11 images

Ride: EB1 Fairmont Ghia T5 Wagon

Location: Seven Hills, Sydney
NSW, Australia

Hey Troyman

I think these vents will really work well with your car and the overall theme.

I still say you should mod the airbox lid top to let some cool air in.

BenJ

 

_________________

BenJ's EB T5 DOHC Ghia Wagon - Current Ride
BenJ's EB GL Sedan - Previous Ride
My respect and thanks go to - snap0964, Paulmac, SWC and MRE-50L

Top
 Profile  
 
 
Posted: Sun Jun 15, 2008 2:25 am 
Moderator
Offline

Posts: 14489

Joined: 7th Nov 2004

Ride: AU XR8

Location: a shit suburb in sydney
NSW, Australia

you got me thinking now ben.
i may mod a spare lid to see what happens..

i was just thinking even with the vent louvers on the vent facing rearward it mite be benificial as i have my custom home made cai catching air from underneath and flowing into the bottom of the airbox and what the engine doesnt suck in will flow out the top of the vent keeping a constant cool airflow?
Top
 Profile  
 
Display posts from previous:
Sort by  
 Page 3 of 10  [ 146 posts ]  Go to page Previous  1, 2, 3, 4, 5, 6 ... 10  Next

Who is online

Users browsing this forum: Google [Bot] and 8 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

 

 

It is currently Thu Mar 28, 2024 9:41 pm All times are UTC + 11 hours

 

 

(c)2014 Total Web Solutions Australia - Australian Web Hosting and Domain Names