|
| Nigel |
|
||
|
Tim. Just looked it up : TFS107 appears to be the one.
M14 * 1.5 thread (I already have the tap from last time ) Switch 1 : On 90, off 85 Switch 2 : On 97, Off 92. Cheers Nigel |
||
| Top | |
||
| TimmyA |
|
|||
|
Thanks for Nigel,
You just tapped out an unused thermo bung did you? I thought 90 may be a little low? How did you find it? I was sure the thermostat opens at 90, so getting it down to 85 to turn the fans off would have never happened? Or it worked ok? Cheers mate, Tim
_________________ 93 Red ED 5spd Manual Build Thread |
|||
| Top | |
|||
| Nigel |
|
||
|
If you were after higher temps the TFS163 and 1164 are also interesting
TFS163 : Sw1 On 95, off 90,Sw2 On 105, off 100 TFS164 : Sw1 On 95, off 90, Sw2 On 120, off 115 .. although they both seem far too high for my liking Nigel |
||
| Top | |
||
| TimmyA |
|
|||
|
yeah wouldn't high speed coming on at 120
 use used the other one did you? that comes on low at 90 and off at 85? how did you find it? once the fans come on low did they ever get it down far enough to turn off again? Cheer,s Tim
_________________ 93 Red ED 5spd Manual Build Thread |
|||
| Top | |
|||
| Nigel |
|
||
|
the one i used was the first one - BMW 7 series at the time although later used in 3 series so more affordable.
I ran lpg and low thermostat so the temps were good. First time I also tapped the rear of the water pump input as this water is post-radiator. meant that when the water was indeed cooling from airflow it turned off, but was hard to seal. Next time I tapped the top of the thermostat outlet pipe, exit side of the thermostat. seemed to work ok as well. Hmm actually i have a new idea for me now. My next use is an EB 5.0 in an XF and i think ill get a boss welded into the inlet hose joiner on the body. Nigel. |
||
| Top | |
||
| TimmyA |
|
|||
|
yeah getting a boss welded on would be the way to go for sure... make it so much easier to seal and you put it exactly where you want it... I do like the idea of putting the temp switch after the radiator though... That does make good sense...
Cheers...
_________________ 93 Red ED 5spd Manual Build Thread |
|||
| Top | |
|||
| Nigel |
|
||
|
on the EB V8 there is a joiner in the lower hose - that would have you sampling temp after theradiator so it would switch on the right temps. I happen to have two of these lying around so that might be a go.
Nigel |
||
| Top | |
||
| EDCoonsta |
|
||
|
hey guys im having trouble findind the right thermo switch to do the thermo fan conversion, i got a set of the ef/el twin thermos, gonna do all the wiring and relaysa myself.. 1st question is do i need a switch to controll 2 speed? like the tfs107? or would the tfs106 be ok? 2nd question is what is the thread? is it m14 1.5?
|
||
| Top | |
||
| snap0964 |
|
|||
|
Have a read of ford-v8-f2/thermo-s-on-nc-5l-t98907.html - particularly the posts covering EECIV ECU control.
_________________ 96 XH Longreach 'S': LPG, Alarm, 3.23:1 LSD, Cruise, Trip Comp, ABS, Power Windows, Mid Series Dome Lt, Climate Ctrl |
|||
| Top | |
|||
| EDCoonsta |
|
||
|
Cheers for the link, Yea ive heard about people using the EECIV to control the fans, Just seems more trouble than what its worth for me at the moment seeings tho id need a J3 adaptor as well, Really wanted a switch from tridon that i can just put in the unused bung in the thermostat housing. seems like the easiest way. Would it really matter if the switch only controlled 1 speed? I'l still be hooking up a relay to the AC so it comes on when the AC is on. more just wanted to know if this tfs106 is going to fit http://www.tridon.com.au/Products/Produ ... 483&P=2014
threads m14 x1.5 90 - 95 C |
||
| Top | |
||
| snap0964 |
|
|||
|
Just a quick threadmine.
Other info regarding using pin 41 in the EECIV V8 ECU's, courtesy of ecu-fuel-system-eec-f21/ford-eec-fuel-injection-information-t70568.html . http://www.myo-p.com/Ford-EEC/EEC%20Hel ... ginal.html Just in case someone searches for this.
_________________ 96 XH Longreach 'S': LPG, Alarm, 3.23:1 LSD, Cruise, Trip Comp, ABS, Power Windows, Mid Series Dome Lt, Climate Ctrl |
|||
| Top | |
|||
| galapogos01 |
|
|||
Posts: 1139 Joined: 27th Feb 2005 Ride: Supercharged EF Fairmont Location: T.I. Performance HQ |
Yep, I have enabled fan control in a number of EB/ED V8 ECUs for customers, via a J3 Chip.
Cheers, Jason
_________________ T.I. Performance - Ford Performance Tuning - J3 Chips & Tuning, Fuel Pumps & Injectors, Camshafts and much more! |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 13 guests |
