|
| CrACk InjECtIoN |
|
||
|
Hi,
I changed my ignition coil because it was dead and now i put a new one in about 2 weeks ago and now the car wont start and i dont have any spark. So i need help as i dont know what to do. I havent changed the leads or plugs but they have done about 30,000KMs and its Dual Fuel as well |
||
| Top | |
||
| evxr6 |
|
|||
|
How's the TFI module? Dizzy cap and rotor in good condition?
|
|||
| Top | |
|||
| CrACk InjECtIoN |
|
||
|
I have changed the Rotor Cap and the dizzy and TFI module are the same since i got the car.
So how do i test the TFI module and dizzy to see if they are getting spark? |
||
| Top | |
||
| evxr6 |
|
|||
|
See if you are getting power on the primary side of the coil (low voltage side) with ignition on.
Just a thought, is the smartlock light coming on? If not, it might be a BEM fault. |
|||
| Top | |
|||
| CrACk InjECtIoN |
|
||
|
I disconnected the Clip on the Ignition Coil and tested it and it read 12v so its getting power,
So if the smart lock icon is ALWAYS on while i am turning the engine over it could be a BEM fault? As the worked yesterday and i drove it around and filled up some LPG and this morning it didnt want to start and no spark |
||
| Top | |
||
| sooty72 |
|
|||
|
TFI module.
 Always replace the TFI module and coil together, or one will kill the other. 
_________________ Yes, I own a Ute. No, I won't help you move! |
|||
| Top | |
|||
| CrACk InjECtIoN |
|
||
|
So how do i replace the TFI Module and how can i test it to see if thats the problem?
|
||
| Top | |
||
| fullyforded |
|
|||
|
{USERNAME} wrote: So how do i replace the TFI Module and how can i test it to see if thats the problem? Easy way is to replace the dizzy, but I'm just lazy
_________________ Au series 1 ute. T5 manual, 2.5" redback zorst, Xtreme HD clutch |
|||
| Top | |
|||
| CrACk InjECtIoN |
|
||
|
Ok, What else can be the problem?
As this was a brand new coil and now it doesnt spark, so either its the Dizzy,TFI Module or leads So i will try new TFI Module and Coil |
||
| Top | |
||
| CrACk InjECtIoN |
|
||
|
Well i installed a new coil and still no spark, SO i think i will buy a new dizzy.
How hard is it to install and adjust the timing? |
||
| Top | |
||
| Mad2 |
|
|||
|
no idea how hard etc etc ... BUT .... remember ta change/swap ova original dizzy gear drive ta ya new dizzy so ya donna get any aux shaft failure
|
|||
| Top | |
|||
| CrACk InjECtIoN |
|
||
|
I am going to get this one: http://www.ebay.com.au/itm/GENUINE-BOSC ... 3ccba50a13
So do i still have to change over the gear? |
||
| Top | |
||
| SWC |
|
||
|
It would be advisable. The gears then match (wear patterns).
|
||
| Top | |
||
| Mad2 |
|
|||
|
my understanding is yes
|
|||
| Top | |
|||
| CrACk InjECtIoN |
|
||
|
Ok, so is it hard to replace that gear?
|
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: Google Adsense [Bot] and 9 guests |
